HP LC2000r HP NetRAID 1M/2M Installation & Configuration - Page 17

Tools You May Need

Get HP LC2000r - NetServer - 128 MB RAM PDF manuals and user guides View all HP LC2000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Chapter 1 Introduction • Technical Reference Cards or labels on the HP Netserver system chassis (for cables and SCSI ID switch settings) • Internet site: http://netserver.hp.com/netserver/ Tools You May Need Please refer to your HP Netserver documentation for the tools needed to open the chassis. Usually a flat 1/4-inch screwdriver and a T15 Torx driver are required. If you need to set SCSI ID switches, a flashlight and a small metal pin, such as a straightened paper clip, will be helpful. An antistatic kit (3M 8501/8502/8505 or equivalent) is strongly recommended. CAUTION All HP NetRAID adapter cards are sensitive to static electricity and can easily be damaged by improper handling. Using a grounding strap is recommended. Read the following information carefully before you handle the accessory: • Leave the adapter card in the antistatic bag until you are ready to install it. • If possible, use an antistatic wrist strap and grounding mat. • Before you remove the adapter board from the bag, touch a grounded, unpainted metal surface on the system to discharge static electricity. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
Chapter 1
Introduction
9
•
Technical Reference Cards or labels on the HP Netserver system chassis
(for cables and SCSI ID switch settings)
•
Internet site:
Tools You May Need
Please refer to your HP Netserver documentation for the tools needed to open the
chassis. Usually a flat 1/4-inch screwdriver and a T15 Torx driver are required. If
you need to set SCSI ID switches, a flashlight and a small metal pin, such as a
straightened paper clip, will be helpful. An antistatic kit (3M 8501/8502/8505 or
equivalent) is strongly recommended.
CAUTION
All HP NetRAID adapter cards are sensitive to static
electricity and can easily be damaged by improper handling.
Using a grounding strap is recommended. Read the following
information carefully before you handle the accessory:
•
Leave the adapter card in the antistatic bag until you are
ready to install it.
•
If possible, use an antistatic wrist strap and grounding
mat.
•
Before you remove the adapter board from the bag, touch a
grounded, unpainted metal surface on the system to
discharge static electricity.