HP LC2000r HP NetRAID 1M/2M Installation & Configuration - Page 82

Microsoft Windows NT Terminal Server Edition

Get HP LC2000r - NetServer - 128 MB RAM PDF manuals and user guides View all HP LC2000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Chapter 6 HP NetRAID Software Microsoft Windows NT Terminal Server Edition NOTE Windows NT Terminal Server Edition must be operating in INSTALL mode when you install the NetRAID Software- NT/Win2000. Otherwise, the administrator may see it as properly installed, but it may fail for other users. There are three relevant commands for the DOS prompt: • CHANGE USER /INSTALL = sets it to install mode. • CHANGE USER /EXECUTE = sets it to execute mode. • CHANGE USER /QUERY = show the current mode of operation. After the installation, return to the default EXECUTE mode. This means that clients connected via the network can connect to the server and run Windows NT sessions from it. 1. Select Start from the taskbar. 2. Choose Run from the Start menu. 3. Insert diskette #1, "NetRAID Software-NT/Win2000." 4. Type :\setup at the Open: prompt, where is the drive letter of the diskette drive you are using. 5. Follow the on-screen instructions. NOTE Setup installs the following HP NetRAID-1M or 2M software: • HP NetRAID Assistant • HP NetRAID Monitor Service • HP NetRAID Consistency Check Scheduler 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
Chapter 6
HP NetRAID Software
74
Microsoft Windows NT Terminal Server Edition
NOTE
Windows NT Terminal Server Edition must be operating in
INSTALL mode when you install the
NetRAID Software—
NT/Win2000
. Otherwise, the administrator may see it as
properly installed, but it may fail for other users.
There are three relevant commands for the DOS prompt:
•
CHANGE USER /INSTALL = sets it to install mode.
•
CHANGE USER /EXECUTE = sets it to execute mode.
•
CHANGE USER /QUERY = show the current mode of
operation.
After the installation, return to the default EXECUTE mode.
This means that clients connected via the network can
connect to the server and run Windows NT sessions from it.
1.
Select
Start
from the taskbar.
2.
Choose
Run
from the Start menu.
3.
Insert diskette #1, "
NetRAID Software—NT/Win2000
."
4.
Type
<d>:\setup
at the Open: prompt, where
<d>
is the drive letter of
the diskette drive you are using.
5.
Follow the on-screen instructions.
NOTE
Setup installs the following HP NetRAID-1M or 2M software:
•
HP NetRAID Assistant
•
HP NetRAID Monitor Service
•
HP NetRAID Consistency Check Scheduler