HP LaserJet P1500 Service Manual - Page 100

Media problem-solving

Get HP LaserJet P1500 PDF manuals and user guides View all HP LaserJet P1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

Media problem-solving The following problems with media cause print-quality deviations, jamming, or damage to the device. Problem Cause Solution Poor print quality or toner adhesion Dropouts, jamming, or curl The paper is too moist, too rough, too heavy or too smooth, or it is embossed or from a faulty paper lot. Try another kind of paper, between 100 and 250 Sheffield, with 4% to 6% moisture content. The paper has been stored incorrectly. Store paper flat in its moisture-proof wrapping. The paper has variability from one side Turn the paper over. to the other. Excessive curl The paper is too moist, has the wrong grain direction, or is of short-grain construction Use long-grain paper. The paper varies from side-to-side. Turn the paper over. Jamming, damage to device The paper has cutouts or perforations. Use paper that is free of cutouts or perforations. Problems with feeding The paper has ragged edges. Use high-quality paper that is made for laser printers. The paper varies from side-to-side. Turn the paper over. The paper is too moist, too rough, too heavy or too smooth, has the wrong grain direction, or is of short-grain construction or it is embossed or from a faulty paper lot. Try another kind of paper, between 100 and 250 Sheffield, 4% to 6% moisture content. Use long-grain paper. Print is skewed (crooked). The media guides might be incorrectly adjusted. Remove all media from the input tray, straighten the stack, and then load the media in the input tray again. Adjust the media guides to the width and length of the media that you are using and try printing again. More than one sheet feeds at one time. The media tray might be overloaded. Remove some of the media from the tray. The media might be wrinkled, folded, or Verify that the media is not wrinkled, damaged. folded, or damaged. Try printing on media from a new or different package. The device does not pull media from the The device might be in manual-feed media input tray. mode. Verify that the device is not in manual feed mode and print your job again. The pickup roller might be dirty or damaged. Contact HP Customer Care. See Contact HP support on page 77or the support flyer that came in the box. The paper-length adjustment control in Adjust the paper-length adjustment main tray is set at a length that is greater control to the correct length. than the media size. 88 Chapter 5 Problem solving ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
Media problem-solving
The following problems with media cause print-quality deviations, jamming, or damage to the device.
Problem
Cause
Solution
Poor print quality or toner adhesion
The paper is too moist, too rough, too
heavy or too smooth, or it is embossed
or from a faulty paper lot.
Try another kind of paper, between 100
and 250 Sheffield, with 4% to 6%
moisture content.
Dropouts, jamming, or curl
The paper has been stored incorrectly.
Store paper flat in its moisture-proof
wrapping.
The paper has variability from one side
to the other.
Turn the paper over.
Excessive curl
The paper is too moist, has the wrong
grain direction, or is of short-grain
construction
Use long-grain paper.
The paper varies from side-to-side.
Turn the paper over.
Jamming, damage to device
The paper has cutouts or perforations.
Use paper that is free of cutouts or
perforations.
Problems with feeding
The paper has ragged edges.
Use high-quality paper that is made for
laser printers.
The paper varies from side-to-side.
Turn the paper over.
The paper is too moist, too rough, too
heavy or too smooth, has the wrong grain
direction, or is of short-grain construction
or it is embossed or from a faulty paper
lot.
Try another kind of paper, between 100
and 250 Sheffield, 4% to 6% moisture
content.
Use long-grain paper.
Print is skewed (crooked).
The media guides might be incorrectly
adjusted.
Remove all media from the input tray,
straighten the stack, and then load the
media in the input tray again. Adjust the
media guides to the width and length of
the media that you are using and try
printing again.
More than one sheet feeds at one time.
The media tray might be overloaded.
Remove some of the media from the tray.
The media might be wrinkled, folded, or
damaged.
Verify that the media is not wrinkled,
folded, or damaged. Try printing on
media from a new or different package.
The device does not pull media from the
media input tray.
The device might be in manual-feed
mode.
Verify that the device is not in manual
feed mode and print your job again.
The pickup roller might be dirty or
damaged.
Contact HP Customer Care. See
Contact
HP support
on page
77
or the support
flyer that came in the box.
The paper-length adjustment control in
main tray is set at a length that is greater
than the media size.
Adjust the paper-length adjustment
control to the correct length.
88
Chapter 5
Problem solving
ENWW