HP Microportable Projector MP2810 Compaq MP2800 Microportable Projector - Page 29

Special On-Screen Messages, Composite Video, Use Source to Change Input°

Get HP Microportable Projector MP2810 PDF manuals and user guides View all HP Microportable Projector MP2810 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Factory Reset-Resets the current operating option to its original factory setting. Special On-Screen Messages Special on-screen messages will appear on the projection display to identify the following conditions: Check Video Cable: Indicates the video cable may not be plugged into the projector or the selected video input is not accurate. Input Signal Out of Range-Indicates the projector is unable to access the appropriate input signal. 2 Inputs Active - Remove One-The projector has two data inputs: one is an analog D-Sub input and the other is a digital DFP input. This message indicates that both inputs are active simultaneously and the user should detach one of them. NOTE: This message appears only when the Multimedia Adapter is not attached to the projector. Going to Standby-Indicates the projector is entering a sleep mode or is powering off the lamp. Lamp May Fail Soon, Replacement Suggested-Indicates the lamp is approaching failure. The message will remain on the screen for five seconds or until the on-screen menu Select button is pressed. When the Multimedia Adapter is attached to the projector, the following messages, in addition to the previous messages, will appear on the projection display to identity the following conditions: Analog, Use Source to Change Input-Indicates analog and video inputs are connected. Since the projector will default to display analog, you must press the Source button to switch to video. Composite Video, Use Source to Change Input-Indicates composite video or other inputs (excluding HDTV) are present. Composite video is the default setting unless HDTV is connected. Press the Source button to change the setting. Using the Projector 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
Using the Projector
29
■
Factory Reset²Resets the current operating option to its original
factory setting.
Special On-Screen Messages
Special on-screen messages will appear on the projection display to
identify the following conditions:
■
Check Video Cable:
Indicates the video cable may not be
plugged into the projector or the selected video input is not
accurate.
■
Input Signal Out of Range°
Indicates the projector is unable to
access the appropriate input signal.
■
2 Inputs Active - Remove One°
The projector has two data
inputs: one is an analog D-Sub input and the other is a digital
DFP input. This message indicates that both inputs are active
simultaneously and the user should detach one of them.
NOTE:
This message appears only when the Multimedia Adapter
is not attached to the projector.
■
Going to Standby°
Indicates the projector is entering a sleep
mode or is powering off the lamp.
■
Lamp May Fail Soon, Replacement Suggested°
Indicates the
lamp is approaching failure. The message will remain on the
screen for five seconds or until the on-screen menu
Select
button
is pressed.
When the Multimedia Adapter is attached to the projector, the
following messages, in addition to the previous messages, will
appear on the projection display to identity the following
conditions:
■
Analog, Use Source to Change Input
²Indicates analog and
video inputs are connected. Since the projector will default to
display analog, you must press the
Source
button to switch to
video.
■
Composite Video, Use Source to Change Input°
Indicates
composite video or other inputs (excluding HDTV) are present.
Composite video is the default setting unless HDTV is
connected. Press the
Source
button to change the setting.