HP Mini 1000 HP Mini 1000 and Compaq Mini 700 - Maintenance and Service Guide - Page 67

Fan, Remove the fan

Get HP Mini 1000 - PC PDF manuals and user guides View all HP Mini 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Fan Description Fan Spare part number 504615-001 NOTE: To properly ventilate the device, allow at least a 7.6-cm (3-inch) clearance on the left side of the device. The device uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to turn on automatically when high temperature conditions exist. These conditions are affected by high external temperatures, system power consumption, power management/battery conservation configurations, battery fast charging, and software requirements. Exhaust air is displaced through the ventilation grill located on the left side of the device. Before removing the fan, follow these steps: 1. Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the device. 3. Disconnect the power from the device by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the device. 4. Remove the battery (see Battery on page 37). 5. Remove the following components: a. Keyboard (see Keyboard on page 40) b. Hard drive or solid-state drive (see Mass storage devices on page 42) c. Top cover (see Top cover on page 45) d. System board (see System board on page 54) Remove the fan: 1. Detach the black mylar covering and tape (see WLAN module on page 48), and then move the cables aside. 2. Remove the Phillips PM2.0×3.0 screw (1) and the Phillips PM2.0×4.5 screw (2) that secure the fan to the base enclosure. Component replacement procedures 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
Fan
Description
Spare part number
Fan
504615-001
NOTE:
To properly ventilate the device, allow at least a 7.6-cm (3-inch) clearance on the left side of
the device. The device uses an electric fan for ventilation. The fan is controlled by a temperature sensor
and is designed to turn on automatically when high temperature conditions exist. These conditions are
affected by high external temperatures, system power consumption, power management/battery
conservation configurations, battery fast charging, and software requirements. Exhaust air is displaced
through the ventilation grill located on the left side of the device.
Before removing the fan, follow these steps:
1.
Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device
on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the device.
3.
Disconnect the power from the device by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the device.
4.
Remove the battery (see
Battery
on page
37
).
5.
Remove the following components:
a.
Keyboard (see
Keyboard
on page
40
)
b.
Hard drive or solid-state drive (see
Mass storage devices
on page
42
)
c.
Top cover (see
Top cover
on page
45
)
d.
System board (see
System board
on page
54
)
Remove the fan:
1.
Detach the black mylar covering and tape (see
WLAN module
on page
48
), and then move the
cables aside.
2.
Remove the Phillips PM2.0×3.0 screw
(1)
and the Phillips PM2.0×4.5 screw
(2)
that secure the fan
to the base enclosure.
Component replacement procedures
59