HP Mini 110-4100ca HP Mini 200 - Maintenance and Service Guide - Page 51

Hard drive, Remove the Phillips PM 2.0×5.0 screw

Get HP Mini 110-4100ca PDF manuals and user guides View all HP Mini 110-4100ca manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Hard drive NOTE: The hard drive spare part kit does not include the hard drive bracket, connector cable, rubber isolators, or screws. These components are included in the Hard Drive Hardware Kit, spare part number 664913-001. Description 500-GB, 5400-rpm 320-GB, 5400-rpm 250-GB, 5400-rpm Spare part number 634932-001 645193-001 645191-001 Before removing the hard drive, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 34). 5. Remove the service cover (see WLAN module on page 36). Remove the hard drive: 1. Disconnect the hard drive connector cable (1) from the system board. 2. Remove the Phillips PM 2.0×5.0 screw (2) that secures the hard drive to the computer. 3. Use the pull tab (3) to lift the left side of the hard drive until it rests at an angle. Component replacement procedures 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Hard drive
NOTE:
The hard drive spare part kit does not include the hard drive bracket, connector cable, rubber
isolators, or screws. These components are included in the Hard Drive Hardware Kit, spare part
number 664913-001.
Description
Spare part number
500-GB, 5400-rpm
634932-001
320-GB, 5400-rpm
645193-001
250-GB, 5400-rpm
645191-001
Before removing the hard drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see
Battery
on page
34
).
5.
Remove the service cover (see
WLAN module
on page
36
).
Remove the hard drive:
1.
Disconnect the hard drive connector cable
(1)
from the system board.
2.
Remove the Phillips PM 2.0×5.0 screw
(2)
that secures the hard drive to the computer.
3.
Use the pull tab
(3)
to lift the left side of the hard drive until it rests at an angle.
Component replacement procedures
43