HP PageWide Managed Color P75250 On-Site Installation Guide - Page 112

Late point differentiation configuration (LPDC) (manually using USB flash drive), Not configured XX

Get HP PageWide Managed Color P75250 PDF manuals and user guides View all HP PageWide Managed Color P75250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

NOTE: The printer automatically re-initializes several times. This might take up to 30 minutes to complete, so make sure not to interrupt the firmware process. 8. After the printer arrives at the "Ready" state, wait another 2-5 minutes to allow the printer firmware to finish copying firmware to all of the PCAs. 9. Print a Configuration Page and make sure that the firmware is correctly upgraded and confirm that the LPDC status is "Not configured (XX, XX, XX)". 10. Press the power button on the front of the printer, and then turn off the power (near the power cord). NOTE: The printer speed cannot be changed after it is set by the LPDC license. The printer serial number is locked to the speed setting, based on what was ordered by the customer, and is placed in HPI's license activation site located in the cloud. TIP: The easiest way to obtain the speed license is to connect the printer to the Internet after upgrading the firmware and allowing the printer to automatically download and transfer the speed license from the HP Cloud. 11. Connect the network cable to the printer. 12. Turn on the main power (near the power cord), and then press the power button on the front of the printer. Wait for the printer to reach the "Ready" state. 13. Make sure that the printer has a valid IP address and a working internet connection. A proxy server might need to be configured at this time in the EWS or directly input into the control panel menu. 14. Wait for the LPDC process to automatically start (within 10 minutes of having a working internet connection). NOTE: The printer reboots after the LPDC process is complete, and the printer setup wizard starts. 15. When the Setup Wizard appears, re-configure each of the settings. 16. Wait at least 5 minutes after the printer comes to a Ready state to allow the LPDC process to complete. CAUTION: Do not turn the printer power off during this time. 17. Print another Configuration Page and make sure that the LPDC is configured with the correct license speed and that the printer model number is correct. The printer product model changes to the ordered model number. In the LPDC status, the first number in the parentheses (x) is either "0", "1" or "2". The "0" corresponds to the slowest speed, "1" is the middle speed, and "2" is the fastest speed. This confirms that the LPDC process is complete. NOTE: If, after connecting the printer to a network to start the LPDC process, the printer repeatedly reboots to the Setup Wizard, go to "Printer repeatedly reboots after attempting the LPDC process" to troubleshoot the issue (ID: c05685029). NOTE: If the automatic installation fails, if no internet connection is available, or if the LPDC process is not possible via the network connection, the speed license can be downloaded to a USB Ʈash drive and manually installed. Late point differentiation configuration (LPDC) (manually using USB flash drive) 106 Chapter 9 Late point differentiation configuration (LPDC) ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
NOTE:
The printer automatically re-initializes several times. This might take up to 30 minutes to
complete, so make sure not to interrupt the firmware process.
8.
After the printer arrives at the “
Ready
” state, wait another 2-5 minutes to allow the printer firmware to
finish copying firmware to all of the PCAs.
9.
Print a Configuration Page and make sure that the firmware is correctly upgraded and confirm that the
LPDC status is “
Not configured (XX, XX, XX)
”.
10.
Press the power button on the front of the printer, and then turn off the power (near the power cord).
NOTE:
The printer speed cannot be changed after it is set by the LPDC license. The printer serial number
is locked to the speed setting, based on what was ordered by the customer, and is placed in HPI’s license
activation site located in the cloud.
TIP:
The easiest way to obtain the speed license is to connect the printer to the Internet after upgrading
the firmware and allowing the printer to automatically download and transfer the speed license from the
HP Cloud.
11.
Connect the network cable to the printer.
12.
Turn on the main power (near the power cord), and then press the power button on the front of the printer.
Wait for the printer to reach the “
Ready
” state.
13.
Make sure that the printer has a valid IP address and a working internet connection. A proxy server might
need to be configured at this time in the EWS or directly input into the control panel menu.
14.
Wait for the LPDC process to automatically start (within 10 minutes of having a working internet
connection).
NOTE:
The printer reboots after the LPDC process is complete, and the printer setup wizard starts.
15.
When the Setup Wizard appears, re-configure each of the settings.
16.
Wait at least 5 minutes after the printer comes to a Ready state to allow the LPDC process to complete.
CAUTION:
Do not turn the printer power off during this time.
17.
Print another Configuration Page and make sure that the LPDC is configured with the correct license speed
and that the printer model number is correct.
The printer product model changes to the ordered model number. In the LPDC status, the first number in
the parentheses (x) is either “0”, “1” or “2”. The “0” corresponds to the slowest speed, “1” is the middle
speed, and “2” is the fastest speed. This confirms that the LPDC process is complete.
NOTE:
If, after connecting the printer to a network to start the LPDC process, the printer repeatedly
reboots to the Setup Wizard, go to “Printer repeatedly reboots after attempting the LPDC process” to
troubleshoot the issue (ID: c05685029).
NOTE:
If the automatic installation fails, if no internet connection is available, or if the LPDC process is not
possible via the network connection, the speed license can be downloaded to a USB
Ʈ
ash drive and
manually installed.
Late point differentiation configuration (LPDC) (manually using USB flash drive)
106
Chapter 9
Late point differentiation configuration (LPDC)
ENWW