HP PageWide Managed Color P75250 On-Site Installation Guide - Page 75

Install accessories, 1x550-sheet feeder, 1x550-sheet feeder with storage cabinet

Get HP PageWide Managed Color P75250 PDF manuals and user guides View all HP PageWide Managed Color P75250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Install accessories ● 1x550-sheet feeder ● 1x550-sheet feeder with storage cabinet ● 3x550-sheet feeder ● 4000-sheet high capacity input (HCI) feeder 1x550-sheet feeder CAUTION: Always turn the printer power off, then unplug the power cord before installing any accessory. 1. Do the following: a. If the printer tray, or trays, were reinstalled after unpacking the printer, remove them now. b. Remove the blue shipping tape from the accessory. c. Before proceeding, take note of the location of the alignment pins on the accessory. 2. Do the following: a. Grasp the printer at the tray cavity and the rear hand holds. b. Lift the printer up, and then set it down on the accessory. Make sure that the alignment pins go into the holes in the chassis. The printer must sit flat on top of the accessory. CAUTION: SFP staging models: This step requires two people. MFP staging models: This step requires three people. The third person should steady the printer when it is picked up. ENWW Install accessories 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Install accessories
●
1x550-sheet feeder
●
1x550-sheet feeder with storage cabinet
●
3x550-sheet feeder
●
4000-sheet high capacity input (HCI) feeder
1x550-sheet feeder
CAUTION:
Always turn the printer power off, then unplug the power cord before installing any accessory.
1.
Do the following:
a.
If the printer tray, or trays, were reinstalled after unpacking the printer, remove them now.
b.
Remove the blue shipping tape from the accessory.
c.
Before proceeding, take note of the location of the alignment pins on the accessory.
2.
Do the following:
a.
Grasp the printer at the tray cavity and the rear hand holds.
b.
Lift the printer up, and then set it down on the accessory. Make sure that the alignment pins go into
the holes in the chassis. The printer must sit flat on top of the accessory.
CAUTION:
SFP staging models
: This step requires two people.
MFP staging models
: This step requires three people. The third person should steady the printer
when it is picked up.
ENWW
Install accessories
69