HP PageWide Managed Color P75250 On-Site Installation Guide - Page 52

HP Embedded Web Server, 3 administrator, 1 Download, No USB Thumbdrive Files Found, USB Thumbdrive

Get HP PageWide Managed Color P75250 PDF manuals and user guides View all HP PageWide Managed Color P75250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

2. Tap the middle of the control-panel display when you see the 1/8 under the logo. Figure 5-1 Open the Pre-boot menu 1 2 3. Select the down arrow ▼ to highlight +3 administrator, and then select OK. 4. If necessary, select the down arrow ▼ to highlight +1 Download, and then select OK. 5. Insert the USB flash drive with the .bdl file on it into the USB port on the printer. NOTE: If the error message No USB Thumbdrive Files Found displays on the control-panel display, try using a different portable storage device. 6. Select the down arrow ▼ to highlight USB Thumbdrive, and then select OK. 7. Select the down arrow ▼ to highlight the .bdl file, and then select OK. NOTE: The upgrade process can take 10 minutes or longer to complete. TIP: If there is more than one .bdl file on the storage device, make sure to select the correct file for this printer. 8. When the message Complete displays on the control-panel display, turn the printer power off, and then on again. 9. Select OK to begin the upgrade. When the upgrade is complete, the printer will initialize to a Ready state. 10. When the upgrade process is complete, print a configuration page and verify that the upgrade firmware version was installed. HP Embedded Web Server NOTE: Staging activity will require updating the firmware in the Pre-boot menu Go to Pre-Boot walk-up firmware upgrade in the Staging chapter. NOTE: The firmware upgrade might take 10 minutes or longer based on the input/output (I/O) transfer rates and the time it takes for the printer to reinitialize. 1. Open an Internet browser window. 2. Enter the printer IP address in the URL line. 3. Select the Firmware Upgrade link from the General tab or from the Troubleshooting tab. 4. Browse to the location that the firmware upgrade file was downloaded to, and then select the firmware file -the file has a .bdl file extension. Select the Install to perform the upgrade. 46 Chapter 5 Firmware upgrade ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
2.
Tap the middle of the control-panel display when you see the
1/8
under the logo.
Figure 5-1
Open the Pre-boot menu
1
2
3.
Select the down arrow
▼
to highlight
+3 administrator
, and then select
OK
.
4.
If necessary, select the down arrow
▼
to highlight
+1 Download
, and then select
OK
.
5.
Insert the USB flash drive with the .bdl file on it into the USB port on the printer.
NOTE:
If the error message
No USB Thumbdrive Files Found
displays on the control-panel display, try
using a different portable storage device.
6.
Select the down arrow
▼
to highlight
USB Thumbdrive
, and then select
OK
.
7.
Select the down arrow
▼
to highlight the .bdl file, and then select
OK
.
NOTE:
The upgrade process can take 10 minutes or longer to complete.
TIP:
If there is more than one .bdl file on the storage device, make sure to select the correct file for this
printer.
8.
When the message
Complete
displays on the control-panel display, turn the printer power off, and then on
again.
9.
Select
OK
to begin the upgrade. When the upgrade is complete, the printer will initialize to a
Ready
state.
10.
When the upgrade process is complete, print a configuration page and verify that the upgrade firmware
version was installed.
HP Embedded Web Server
NOTE:
Staging activity will require updating the firmware in the Pre-boot menu Go to Pre-Boot walk-up
firmware upgrade in the Staging chapter.
NOTE:
The firmware upgrade might take 10 minutes or longer based on the input/output (I/O) transfer rates
and the time it takes for the printer to reinitialize.
1.
Open an Internet browser window.
2.
Enter the printer IP address in the URL line.
3.
Select the
Firmware Upgrade
link from the
General
tab or from the
Troubleshooting
tab.
4.
Browse to the location that the firmware upgrade file was downloaded to, and then select the firmware file
—the file has a .bdl file extension. Select the
Install
to perform the upgrade.
46
Chapter 5
Firmware upgrade
ENWW