HP Pavilion 15-bk000 Maintenance and Service Guide - Page 43

Hard drive, drive cable from the system board.

Get HP Pavilion 15-bk000 PDF manuals and user guides View all HP Pavilion 15-bk000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Hard drive NOTE: The hard drive spare part kit does not include the hard drive bracket or cable. The hard drive bracket and cable are included in the Hard Drive Kit, spare part number 808238-001. Description 1-TB, 5400-rpm, SATA, 7.2-mm hard drive 500-GB, 5400-rpm, SATA, 7.0-mm hard drive 500-GB, 5400-rpm, SATA, 8-GB hybrid, 7.0-mm, solid-state hard drive Spare part number 762990-005 778186-005 732000-005 Before removing the hard drive, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the keyboard/top cover (see Keyboard/top cover on page 28). 5. Disconnect the battery cable from the system board (see Battery on page 33). Remove the hard drive: 1. Release the ZIF connector (1) to which the hard drive cable is connected, and then disconnect the hard drive cable from the system board. 2. Use the tab (2) to lift the front edge of the hard drive (3) until it rests at an angle. 3. Remove the hard drive (4) by sliding it up and forward at an angle. 4. If it is necessary to replace the hard drive bracket, separate the left and right sides of the bracket (1) from the hard drive, and then remove the hard drive bracket (2). Component replacement procedures 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Hard drive
NOTE:
The hard drive spare part kit does not include the hard drive bracket or cable. The hard drive bracket
and cable are included in the Hard Drive Kit, spare part number 808238-001.
Description
Spare part number
1-TB, 5400-rpm, SATA, 7.2-mm hard drive
762990-005
500-GB, 5400-rpm, SATA, 7.0-mm hard drive
778186-005
500-GB, 5400-rpm, SATA, 8-GB hybrid, 7.0-mm, solid-state hard drive
732000-005
Before removing the hard drive, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation,
turn the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the keyboard/top cover (see
Keyboard/top cover
on page
28
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
33
).
Remove the hard drive:
1.
Release the ZIF connector
(1)
to which the hard drive cable is connected, and then disconnect the hard
drive cable from the system board.
2.
Use the tab
(2)
to lift the front edge of the hard drive
(3)
until it rests at an angle.
3.
Remove the hard drive
(4)
by sliding it up and forward at an angle.
4.
If it is necessary to replace the hard drive bracket, separate the left and right sides of the bracket
(1)
from the hard drive, and then remove the hard drive bracket
(2)
.
Component replacement procedures
35