HP Pavilion dv5-2100 HP Pavilion dv5 Entertainment PC - Maintenance and Servic - Page 67

Remove the WWAN module by pulling the module away from the slot at an angle.

Get HP Pavilion dv5-2100 - Entertainment Notebook PC PDF manuals and user guides View all HP Pavilion dv5-2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Remove the WWAN module: 1. Disconnect the WWAN antenna cables from the terminals on the WWAN module. NOTE: The 1/red WWAN antenna cable is connected to the WWAN module 1/Main terminal. The 2/blue WWAN antenna cable is connected to the WWAN module 2/Aux terminal. 2. Remove the two Phillips PM2.0×4.0 screws that secure the WWAN module to the system board. (The WWAN module tilts up.) 3. Remove the WWAN module by pulling the module away from the slot at an angle. NOTE: If the WWAN antennas are not connected to the terminals on the WWAN module, the protective sleeves must be installed on the antenna connectors, as shown in the following illustration. Component replacement procedures 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Remove the WWAN module:
1.
Disconnect the WWAN antenna cables from the terminals on the WWAN module.
NOTE:
The 1/red WWAN antenna cable is connected to the WWAN module 1/Main
terminal. The 2/blue WWAN antenna cable is connected to the WWAN module 2/Aux terminal.
2.
Remove the two Phillips PM2.0×4.0 screws that secure the WWAN module to the system board.
(The WWAN module tilts up.)
3.
Remove the WWAN module by pulling the module away from the slot at an angle.
NOTE:
If the WWAN antennas are not connected to the terminals on the WWAN module, the
protective sleeves must be installed on the antenna connectors, as shown in the following illustration.
Component replacement procedures
57