HP Q1581A HP StorageWorks DAT USB Tape Drives User Guide (DW049-90902, Novembe - Page 23

Installing an internal DAT tape drive, Prepare mounting bay

Get HP Q1581A - StorageWorks DAT 160 USB External Tape Drive PDF manuals and user guides
UPC - 882780612716
View all HP Q1581A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

3 Installing an internal DAT tape drive In this chapter: • "Prepare mounting bay" on page 23 • "Attach mounting hardware" on page 24 • "Install drive" on page 25 • "Attach USB cable" on page 25 • "Attach USB and power cable to the tape drive" on page 28 • "Secure the drive" on page 30 Please refer to "Installing an external DAT tape drive" on page 31, if you are installing an external DAT tape drive. Where the illustrations in this chapter show only the HP StorageWorks DAT 320 tape drive, the process is the same for all models of tape drive. Prepare mounting bay You need one industry-standard, 5¼-inch, half-height bay in which to install the HP StorageWorks DAT tape drive. Different models of server require different mounting methods. Refer to your server documentation for detailed information. WARNING! To avoid personal injury or damage to the server or tape drive, ensure that the server is disconnected from the mains power supply while you install the drive. CAUTION: Static electricity can damage electronic components. Always wear an antistatic wriststrap if one is available. If not, after you have disconnected power from the server and removed the cover, touch a bare metal part of the chassis. Similarly, touch a bare metal part of the drive before installing it. 1. Refer to your server documentation for detailed instructions and assemble the necessary tools and materials. 2. Perform a normal system shutdown and turn off the server and any connected peripherals. 3. Remove the cover and access panel from the server, as detailed in your server's documentation. As you work inside the server, you may have to disconnect other signal cables or power cables from other devices to maneuver the new drive into place. If you have to do this, make a note of their position and connections so you can put them back correctly later. DAT USB Tape Drives 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
3 Installing an internal DAT tape drive
In this chapter:
•
“
Prepare mounting bay
” on page 23
•
“
Attach mounting hardware
” on page 24
•
“
Install drive
” on page 25
•
“
Attach USB cable
” on page 25
•
“
Attach USB and power cable to the tape drive
” on page 28
•
“
Secure the drive
” on page 30
Please refer to “
Installing an external DAT tape drive
” on page 31, if you are installing an external
DAT tape drive.
Where the illustrations in this chapter show only the HP StorageWorks DAT 320 tape drive, the
process is the same for all models of tape drive.
Prepare mounting bay
You need one industry-standard, 5¼-inch, half-height bay in which to install the HP StorageWorks
DAT tape drive. Different models of server require different mounting methods. Refer to your server
documentation for detailed information.
WARNING!
To avoid personal injury or damage to the server or tape drive, ensure that the server is disconnected
from the mains power supply while you install the drive.
CAUTION:
Static electricity can damage electronic components. Always wear an antistatic wriststrap if one is
available. If not, after you have disconnected power from the server and removed the cover, touch a
bare metal part of the chassis. Similarly, touch a bare metal part of the drive before installing it.
1.
Refer to your server documentation for detailed instructions and assemble the necessary tools
and materials.
2.
Perform a normal system shutdown and turn off the server and any connected peripherals.
3.
Remove the cover and access panel from the server, as detailed in your server's documentation.
As you work inside the server, you may have to disconnect other signal cables or power cables
from other devices to maneuver the new drive into place. If you have to do this, make a note of
their position and connections so you can put them back correctly later.
DAT USB Tape Drives
23