HP Q1581A HP StorageWorks DAT USB Tape Drives User Guide (DW049-90902, Novembe - Page 26

To check whether your server has an internal USB port:, Connect the USB cable to an internal USB port

Get HP Q1581A - StorageWorks DAT 160 USB External Tape Drive PDF manuals and user guides
UPC - 882780612716
View all HP Q1581A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Three USB cables are provided with the tape drive to support connection to three types of internal USB port: • A USB cable with a 4-pin Intel connector (blue) • A USB cable with a 4-pin ProLiant connector (red) • A standard USB cable NOTE: If your server does not have an internal USB port, you must purchase and install a separate USB HBA with an internal port before you install the tape drive. See http://www.hp.com/go/connect for recommended products. To check whether your server has an internal USB port: • Look at the diagram on the inside of the side panel of the server to establish whether the server has an internal USB port and its location. The internal USB port may have a 4-pin or a standard USB connector. • The 4-pin USB connector on the system board may be orientated vertically or horizontally. Figure 7 Orientation of internal 4-pin connector (ProLiant header pin layout) . Connect the USB cable to an internal USB port 1. Use the schematic on the inside of the server panel to check whether your server has an internal USB 2.0 port and locate its position. If it does not have an internal USB port, you must first install a USB HBA. See http://www.hp.com/ go/connect for recommended products. 26 Installing an internal DAT tape drive

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Three USB cables are provided with the tape drive to support connection to three types of internal
USB port:
•
A USB cable with a 4–pin Intel connector (blue)
•
A USB cable with a 4–pin ProLiant connector (red)
•
A standard USB cable
NOTE:
If your server does not have an internal USB port, you must purchase and install a separate USB HBA
with an internal port before you install the tape drive. See
h
t
tp://w
w
w
.hp
.co
m/g
o/co
nn
ec
t
for
recommended products.
To check whether your server has an internal USB port:
•
Look at the diagram on the inside of the side panel of the server to establish whether the server
has an internal USB port and its location. The internal USB port may have a 4-pin or a standard
USB connector.
•
The 4-pin USB connector on the system board may be orientated vertically or horizontally.
Figure 7 Orientation of internal 4-pin connector (ProLiant header pin layout)
.
Connect the USB cable to an internal USB port
1.
Use the schematic on the inside of the server panel to check whether your server has an internal
USB 2.0 port and locate its position.
If it does not have an internal USB port, you must first install a USB HBA. See
h
t
tp://w
w
w
.hp
.co
m/
go/co
nnec
t
for recommended products.
Installing an internal DAT tape drive
26