HP R1500 HP UPS R3000 User Guide - Page 11

UPS R3000 INT rear panel, REPO port

Get HP R1500 - UPS XR PDF manuals and user guides View all HP R1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

UPS R3000 INT rear panel Item 1 2 3 4 5 6 7 8 9 10 11 Description REPO port ERM connector Serial communications port/options slot Load segment 1 (three IEC-320-C13 receptacles) Load segment 2 (three IEC-320-C13 receptacles) Load segment 3 (three IEC-320-C13 receptacles) Load segment circuit breakers PDU output (IEC-320-C20) receptacle (load segment 1) Cord retention clip attachment locations Input power receptacle (IEC-320-C19) for country-specific plug attachment Ground bonding screw REPO port The UPS includes an isolated REPO port. When properly wired, the REPO feature enables the power at the UPS output receptacles to be switched off from a remote location. To use this feature, the REPO port must be connected to a remote, normally open switch (not supplied). The REPO switch is used in conjunction with a main disconnect device that removes the AC source from the input of the UPS. When the switch is closed: • The REPO feature immediately powers down protected devices and does not utilize the orderly shutdown procedure initiated by power management software. • The REPO feature shuts down UPS units operating under either utility or battery power. Component identification 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
Component identification 11
UPS R3000 INT rear panel
Item
Description
1
REPO port
2
ERM connector
3
Serial communications port/options slot
4
Load segment 1 (three IEC-320-C13 receptacles)
5
Load segment 2 (three IEC-320-C13 receptacles)
6
Load segment 3 (three IEC-320-C13 receptacles)
7
Load segment circuit breakers
8
PDU output (IEC-320-C20) receptacle (load segment 1)
9
Cord retention clip attachment locations
10
Input power receptacle (IEC-320-C19) for country-specific plug
attachment
11
Ground bonding screw
REPO port
The UPS includes an isolated REPO port. When properly wired, the REPO feature enables the power at
the UPS output receptacles to be switched off from a remote location. To use this feature, the REPO port
must be connected to a remote, normally open switch (not supplied). The REPO switch is used in
conjunction with a main disconnect device that removes the AC source from the input of the UPS. When
the switch is closed:
•
The REPO feature immediately powers down protected devices and does not utilize the orderly
shutdown procedure initiated by power management software.
•
The REPO feature shuts down UPS units operating under either utility or battery power.