Home » HP Manuals » UPS » HP R1500 » Manual Viewer

HP R1500 HP UPS R3000 User Guide - Page 18

Installing the UPS

Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

6. Install the rear stabilization bracket using hex nuts. Wait until the unit is installed and the brackets are adjusted before tightening the nuts. Installing the UPS Before installing the unit, review and adhere to all warnings provided in "Precautions (on page 13)." WARNING: A risk of personal injury or damage to the equipment exists. Uneven loading of equipment in the rack might cause the rack to become unstable. Install the heavier components first, and then continue to populate the rack from the bottom to the top. 1. Install the mounting rails ("Installing the mounting rails" on page 14). 2. With one person on each side, lift the chassis to rail level and slide the chassis on the mounting rails. 3. Attach the chassis to the rack using the supplied screws. Installation 18

Section	Page
HP UPS R3000 User Guide	1
Notice	2
Contents	3
Component identification	6
UPS R3000 overview	6
UPS front panel	6
UPS front panel controls	7
UPS front panel LED indicators	8
HP UPS R3000 models	8
UPS R3000 NA and R3000j JPN rear panel	9
UPS R3000h NA and R3000h JPN rear panel	10
UPS R3000 INT rear panel	11
REPO port	11
ERM rear panel	12
Installation	13
Precautions	13
Preparing to install the hardware	13
Tools and materials	13
Selecting a site	14
Readying the equipment	14
Installing the mounting rails	14
Installing the UPS	18
Connecting the battery leads	19
Attaching the UPS front bezel	19
Connecting the serial communications port	19
Connecting the REPO port	20
Connecting the ground bonding cable	22
Connecting the UPS to utility power	22
Connecting devices to the UPS	23
Connecting the UPS cord retention clips	23
Charging the UPS batteries	24
Starting power to the load	24
Installing the ERM	24
Attaching the ERM front bezel	25
Switching off the ERM circuit breaker	25
Connecting the ERM to the UPS	25
Switching on the ERM circuit breaker	26
Charging the ERM batteries	26
UPS operations	27
Modes of operation	27
Standby mode	27
Operate mode	27
Configure mode	28
Auto-Bypass mode	28
Configuring the UPS	28
Available voltage settings	30
Initiating a self-test	30
Silencing an audible alarm	31
Verifying the REPO port connection	31
Powering down the UPS	31
Power management	32
Power management software	32
Maintenance	33
Removing the UPS front bezel	33
Removing the ERM front bezel	33
Replacing the UPS electronics module	33
Replacing the UPS option card	34
Replacing the batteries	35
Important battery safety information	35
Battery care and storage guidelines	36
Determining when to replace batteries	36
Obtaining new batteries	36
UPS battery replacement procedure	36
Testing the new battery module	38
Replacing the UPS	38
Replacing the ERM	38
Updating the UPS firmware	39
Configuring a USB to serial converter	39
Reassigning the USB COM ports	40
Troubleshooting	41
LED and audible alarm troubleshooting	41
UPS is in Auto-Bypass mode	42
General alarm condition	42
Bypass is out of range	43
Battery condition	43
UPS is on battery	43
Input voltage is out of range	43
Utility power condition	44
Internal UPS fault condition	44
REPO condition	44
Site wiring condition	44
Overload condition	44
UPS does not start	44
Low battery shutdowns	45
UPS does not provide the expected backup time	45
UPS frequently switches between utility and battery power	45
ERM cannot be configured from the UPS front panel	45
Specifications	46
UPS physical specifications	46
ERM physical specifications	46
UPS input specifications	46
UPS output specifications	47
Power protection specifications	47
Voltage specifications	47
Output tolerance specifications	48
Output feature specifications	48
Battery specifications	48
Battery runtime	48
Environmental specifications	49
REPO port specifications	49
Spares	50
Ordering spares	50
UPS spare parts list	50
ERM spare parts list	51
Hardware options	51
Technical support	52
Before you contact HP	52
HP contact information	52
Warranty information	53
Limited warranty	53
$250,000 Computer Load Protection Guarantee	53
Pre-Failure Battery Warranty	53
Recommended duration of use	54
Regulatory compliance notices	55
Regulatory compliance identification numbers	55
Federal Communications Commission notice	55
FCC rating label	55
Class A equipment	55
Class B equipment	55
Declaration of conformity for products marked with the FCC logo, United States only	56
Modifications	56
Cables	56
Canadian notice (Avis Canadien)	57
European Union regulatory notice	57
Disposal of waste equipment by users in private households in the European Union	57
Japanese notice	58
BSMI notice	59
Korean notice	59
Battery replacement notice	59
Taiwan battery recycling notice	60
Power cord statement for Japan	60
Electrostatic discharge	61
Preventing electrostatic discharge	61
Grounding methods to prevent electrostatic discharge	61
Acronyms and abbreviations	62

Match case Limit results 1 per page

Installation 18

Install the rear stabilization bracket using hex nuts. Wait until the unit is installed and the brackets

are adjusted before tightening the nuts.

Installing the UPS

Before installing the unit, review and adhere to all warnings provided in "Precautions (on page

)."

WARNING:

A risk of personal injury or damage to the equipment exists. Uneven loading of

equipment in the rack might cause the rack to become unstable. Install the heavier

components first, and then continue to populate the rack from the bottom to the top.

Install the mounting rails ("

Installing the mounting rails

" on page

With one person on each side, lift the chassis to rail level and slide the chassis on the mounting rails.

Attach the chassis to the rack using the supplied screws.