HP Spectre XT TouchSmart Ultrabook CTO 15t-4000 HP SpectreXT TouchSmart Mainte - Page 52

that secure the hard drive bracket to, Remove the four Phillips PM3.0×3.3 screws

Get HP Spectre XT TouchSmart Ultrabook CTO 15t-4000 PDF manuals and user guides View all HP Spectre XT TouchSmart Ultrabook CTO 15t-4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

3. Remove the hard drive (3). NOTE: As the hard drive is being removed, make sure the hard drive cable is released from beneath the multimedia board cable (4). 4. If it is necessary to disassemble the hard drive, perform the following steps: a. Position the hard drive with the connector toward you. b. Disconnect the hard drive connector cable (1) from the hard drive. c. Remove the four Phillips PM3.0×3.3 screws (2) that secure the hard drive bracket to the hard drive. d. Remove the hard drive bracket (3) from the hard drive. The hard drive bracket, hard drive connector cable, and screws are available in the Hard Drive Hardware Kit, spare part number 700805-001. 44 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
3.
Remove the hard drive
(3)
.
NOTE:
As the hard drive is being removed, make sure the hard drive cable is released from
beneath the multimedia board cable
(4)
.
4.
If it is necessary to disassemble the hard drive, perform the following steps:
a.
Position the hard drive with the connector toward you.
b.
Disconnect the hard drive connector cable
(1)
from the hard drive.
c.
Remove the four Phillips PM3.0×3.3 screws
(2)
that secure the hard drive bracket to
the hard drive.
d.
Remove the hard drive bracket
(3)
from the hard drive.
The hard drive bracket, hard drive connector cable, and screws are available in the Hard
Drive Hardware Kit, spare part number 700805-001.
44
Chapter 4
Removal and replacement procedures