HP Spectre XT TouchSmart Ultrabook CTO 15t-4000 HP SpectreXT TouchSmart Mainte - Page 53

Display assembly subcomponents, Reverse this procedure to reassemble and install the hard drive.

Get HP Spectre XT TouchSmart Ultrabook CTO 15t-4000 PDF manuals and user guides View all HP Spectre XT TouchSmart Ultrabook CTO 15t-4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Reverse this procedure to reassemble and install the hard drive. Display assembly subcomponents NOTE: The display assembly is spared at the subcomponent level only. For more display assembly spare part information, see the individual removal subsections. To remove the display assembly and access the display assembly subcomponents, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 33). 5. Disconnect the battery cable from the system board (see Battery on page 35). Remove the display assembly: 1. Open the computer and rest it on its keyboard. 2. Disconnect the display panel touch cable (1) from the system board. 3. Detach the display panel touch cable (2) from the system board. (The display panel touch cable is attached to the system board with double-sided tape.) 4. Disconnect the display panel cable (3) from the system board. 5. Release the display panel cable (4) from the retention clip (5) built into the right display hinge. Component replacement procedures 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
Reverse this procedure to reassemble and install the hard drive.
Display assembly subcomponents
NOTE:
The display assembly is spared at the subcomponent level only. For more display assembly
spare part information, see the individual removal subsections.
To remove the display assembly and access the display assembly subcomponents, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
33
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
35
).
Remove the display assembly:
1.
Open the computer and rest it on its keyboard.
2.
Disconnect the display panel touch cable
(1)
from the system board.
3.
Detach the display panel touch cable
(2)
from the system board. (The display panel touch cable is
attached to the system board with double-sided tape.)
4.
Disconnect the display panel cable
(3)
from the system board.
5.
Release the display panel cable
(4)
from the retention clip
(5)
built into the right display hinge.
Component replacement procedures
45