HP XP20000/XP24000 HP StorageWorks XP Disk Array Configuration Guide (T5278-96 - Page 34

Setting the system option modes, Configuring the Fibre Channel ports

Get HP XP20000/XP24000 PDF manuals and user guides View all HP XP20000/XP24000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Table 8 Host group modes (options) Windows Host Group Mode 6 Function Default Parameter Setting Failure for TPRLO Inactive When using the Emulex FCA in the Windows environment, the parameter setting for TPRLO failed. After receiving TPRLO and FCP_CMD, respectively. PRLO will respond when HostMode=0x0C/ 0x2C and HostModeOption=0x06. (MAIN Ver.50-03-14-00/00 and later) 13 SIM report at link failure. Inactive Select HMO 13 when you want SIM notification when the number of link failures detected between ports exceeds the threshold. 40 V-Vol expansion. Inactive Select HMO 40 when all of the following conditions are satisfied: • The host mode 0C Windows or 2C Windows Extension is used. • You want to automate recognition of the DP-VOL capacity after increasing the DP-VOL capacity. CAUTION: Changing host group modes for ports where servers are already installed and configured is disruptive and requires the server to be rebooted. Setting the system option modes The HP service representative sets the system option mode(s) based on the operating system and software configuration of the host. Notify your HP representative if you install storage agnostic software (such as backup or cluster software) that might require specific settings. Configuring the Fibre Channel ports Configure the disk array Fibre Channel ports by using P9000 or XP Command View Advanced Edition Software or XP Remote Web Console (shown). Select the settings for each port based on your SAN topology. Use switch zoning if you connect different types of hosts to the array through the same switch. 34 Windows

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
Table 8 Host group modes (options) Windows
Default
Function
Host Group
Mode
Inactive
Parameter Setting Failure for TPRLO
When using the Emulex FCA in the Windows environment, the
parameter setting for TPRLO failed. After receiving TPRLO and
FCP_CMD, respectively. PRLO will respond when HostMode=0x0C/
0x2C and HostModeOption=0x06. (MAIN Ver.50-03-14-00/00
and later)
6
Inactive
SIM report at link failure.
Select HMO 13 when you want SIM notification when the number
of link failures detected between ports exceeds the threshold.
13
Inactive
V-Vol expansion.
Select HMO 40 when all of the following conditions are satisfied:
•
The host mode 0C Windows or 2C Windows Extension is used.
•
You want to automate recognition of the DP-VOL capacity after
increasing the DP-VOL capacity.
40
CAUTION:
Changing host group modes for ports where servers are already installed and
configured is disruptive and requires the server to be rebooted.
Setting the system option modes
The HP service representative sets the system option mode(s) based on the operating system and
software configuration of the host. Notify your HP representative if you install storage agnostic
software (such as backup or cluster software) that might require specific settings.
Configuring the Fibre Channel ports
Configure the disk array Fibre Channel ports by using P9000 or XP Command View Advanced
Edition Software or XP Remote Web Console (shown). Select the settings for each port based on
your SAN topology. Use switch zoning if you connect different types of hosts to the array through
the same switch.
34
Windows