HP Xw460c HP ProLiant xw460c Workstation Blade: Maintenance and Service Guide - Page 12

Power down the workstation blade, Remove the workstation blade

Get HP Xw460c - ProLiant - Blade Workstation PDF manuals and user guides View all HP Xw460c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

HP Confidential Power down the workstation blade Before powering down the workstation blade for any upgrade or maintenance procedures, perform a backup of critical workstation data and programs. Depending on the Onboard Administrator configuration, use one of the following methods to power down the workstation blade: • Use a virtual power button selection through iLO 2. This method initiates a controlled remote shutdown of applications and the OS before the workstation blade enters standby mode. • Press and release the Power On/Standby button. This method initiates a controlled shutdown of applications and the OS before the workstation blade enters standby mode. • Press and hold the Power On/Standby button for more than 4 seconds to force the workstation blade to shut down. This method forces the workstation blade to enter standby mode without properly exiting applications and the OS. It provides an emergency shutdown method in the event of a hung application. IMPORTANT: When the workstation blade is in standby mode, auxiliary power is still being provided. To remove all power from the workstation blade, remove the workstation blade from the enclosure. After initiating a virtual power down command, be sure that the workstation blade goes into standby mode by observing that the system power LED is amber. Remove the workstation blade To remove the component: 1. Identify the proper workstation blade. 2. Power down the workstation blade (on page 12). Removal and replacement procedures 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
HP Confidential
Removal and replacement procedures
12
Power down the workstation blade
Before powering down the workstation blade for any upgrade or maintenance procedures, perform a
backup of critical workstation data and programs.
Depending on the Onboard Administrator configuration, use one of the following methods to power down
the workstation blade:
•
Use a virtual power button selection through iLO 2.
This method initiates a controlled remote shutdown of applications and the OS before the
workstation blade enters standby mode.
•
Press and release the Power On/Standby button.
This method initiates a controlled shutdown of applications and the OS before the workstation blade
enters standby mode.
•
Press and hold the Power On/Standby button for more than 4 seconds to force the workstation blade
to shut down.
This method forces the workstation blade to enter standby mode without properly exiting
applications and the OS. It provides an emergency shutdown method in the event of a hung
application.
IMPORTANT:
When the workstation blade is in standby mode, auxiliary power is still being
provided. To remove all power from the workstation blade, remove the workstation blade from
the enclosure.
After initiating a virtual power down command, be sure that the workstation blade goes into standby
mode by observing that the system power LED is amber.
Remove the workstation blade
To remove the component:
1.
Identify the proper workstation blade.
2.
Power down the workstation blade (on page
12
).