HP Xw460c HP ProLiant xw460c Workstation Blade: Maintenance and Service Guide - Page 41

connector boards to the riser board in the following order

Get HP Xw460c - ProLiant - Blade Workstation PDF manuals and user guides View all HP Xw460c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

HP Confidential 5. Carefully pull up on the front and right sides of the PCIe card cage to disengage it from the anchoring pins on the expansion blade enclosure, and then lift the PCIe card cage out of the expansion blade enclosure (2). When replacing the PCIe card cage, reverse the removal procedures. Please note: • To replace the cage, position the cage over the expansion blade enclosure, align the slots on the right and left sides of the card cage with the anchoring pins, and then push down until the card cage is firmly seated. • The PCIe/SAS connectors on the riser board are labeled 1 through 4. Each mezzanine connector board has two connectors labeled J3 and J4. The PCIe/SAS cables connect the mezzanine connector boards to the riser board in the following order: o Connect the first long PCIe/SAS cable (J3) to the first riser connector (number1). o Connect the second long PCIe/SAS cable (J4) to the second riser connector (number 2). o Connect the first short PCIe/SAS cable (J3) to the thirds riser connector (number 3). o Connect the second short PCIe/SAS cable (J4) to the fourth riser connector (number 4). Removal and replacement procedures 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
HP Confidential
Removal and replacement procedures
41
5.
Carefully pull up on the front and right sides of the PCIe card cage to disengage it from the
anchoring pins on the expansion blade enclosure, and then lift the PCIe card cage out of the
expansion blade enclosure (2).
When replacing the PCIe card cage, reverse the removal procedures. Please note:
•
To replace the cage, position the cage over the expansion blade enclosure, align the slots on the
right and left sides of the card cage with the anchoring pins, and then push down until the card
cage is firmly seated.
•
The PCIe/SAS connectors on the riser board are labeled 1 through 4. Each mezzanine connector
board has two connectors labeled J3 and J4. The PCIe/SAS cables connect the mezzanine
connector boards to the riser board in the following order:
o
Connect the first long PCIe/SAS cable (J3) to the first riser connector (number1).
o
Connect the second long PCIe/SAS cable (J4) to the second riser connector (number 2).
o
Connect the first short PCIe/SAS cable (J3) to the thirds riser connector (number 3).
o
Connect the second short PCIe/SAS cable (J4) to the fourth riser connector (number 4).