HP Z840 Maintenance and Service Guide - Page 40

Heading, Option, Description, Changes, SATA2 <MFG MODEL> If installed

Get HP Z840 PDF manuals and user guides View all HP Z840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Heading Option Device Configurations Secure Boot Configuration Power Options Description - Hard Drive - USB Hard Drive - Hard Drive Name - Network Controller (This option is available only if the workstation is connected to a network.) Use the arrow keys to move the cursor to a listed device, and then perform one of the following actions: ● Press Enter to select or deselect the device. ● Use the arrow keys to move a selected device up or down in the boot order. Press F10 to accept the new boot order. ● For a selected device, press F5 to enable or disable it as a bootable device. MS-DOS drive lettering assignments might not apply after an operating system other than MS-DOS has started. Boot devices can be disabled in the boot order process. These order changes are stored in the physical ROM when the F10 Setup changes are confirmed. Select Main, select Save Changes, and then select Exit. You can temporarily override the boot order. To start one time from a device other than the default device specified in Boot Order, restart the workstation and press F9 when the F9=Boot Menu message appears on the screen. After POST completes, a list of bootable devices is displayed. Use the arrow keys to select the preferred bootable device, and then press Enter. The workstation then starts from the selected non-default device for this one time. Lists installed storage devices and provides options for obtaining specific information about each device: To see additional information about a device, use the Up and Down arrow keys to see a device and press Enter to show additional details about the device if available. Hard Disk ● SATA0 , (If installed) ● SATA1 , (If installed) ● SATA5 , (If mSATA installed in SLOT2) CD-ROM ● SATA2 (If installed) ● Legacy Support-(Enable/Disable) ● Secure Boot-(Enable/Disable) ● Key Management - Clear Secure Boot Keys-(Clear/Don't Clear) - Key Ownership-(HP Keys/Custom Keys) ● Fast Boot-(Enable/Disable) For more information on secure boot management go to http://h10025.www1.hp.com/ ewfrf/wc/document?docname=c03653226&cc=us&dlc=en&lc=en. Enables you to set the following: ● Operating System Power Options 30 Chapter 2 System management

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
Heading
Option
Description
—
Hard Drive
— USB Hard Drive
—
Hard Drive Name
—
Network Controller (This option is available only if the workstation is
connected to a network.)
Use the arrow keys to move the cursor to a listed device, and then perform one of the
following actions:
●
Press
Enter
to select or deselect the device.
●
Use the arrow keys to move a selected device up or down in the boot order. Press
F10
to accept the new boot order.
●
For a selected device, press
F5
to enable or disable it as a bootable device.
MS-DOS drive lettering assignments might not apply after an operating system other
than MS-DOS has started.
Boot devices can be disabled in the boot order process. These order changes are stored
in the physical ROM when the F10 Setup changes are
confirmed.
Select
Main
, select
Save
Changes
, and then select
Exit
.
You can temporarily override the boot order. To start one time from a device other than
the default device
specified
in Boot Order, restart the workstation and press
F9
when the
F9=Boot Menu message appears on the screen. After POST completes, a list of bootable
devices is displayed. Use the arrow keys to select the preferred bootable device, and
then press
Enter.
The workstation then starts from the selected non-default device for
this one time.
Device
Configurations
Lists installed storage devices and provides options for obtaining
specific
information
about each device:
To see additional information about a device, use the
Up
and
Down
arrow keys to see a
device and press
Enter
to show additional details about the device if available.
Hard Disk
●
SATA0 <DRIVE CAPACITY>, <DRIVE MFG and/or MODEL> (If installed)
●
SATA1 <DRIVE CAPACITY>, <DRIVE MFG and/or MODEL> (If installed)
●
SATA5 <DRIVE CAPACITY>, <mSATA DRIVE MFG and/or MODEL> (If mSATA installed
in SLOT2)
CD-ROM
●
SATA2 <MFG MODEL> (If installed)
Secure Boot
Configuration
●
Legacy Support—(Enable/Disable)
●
Secure Boot—(Enable/Disable)
●
Key Management
—
Clear Secure Boot Keys—(Clear/Don't Clear)
—
Key Ownership—(HP Keys/Custom Keys)
●
Fast Boot—(Enable/Disable)
For more information on secure boot management go to
ewfrf/wc/document?docname=c03653226&cc=us&dlc=en&lc=en
.
Power Options
Enables you to set the following:
●
Operating System Power Options
30
Chapter 2
System management