Home » HP Manuals » Desktops » HP Z840 » Manual Viewer

HP Z840 Maintenance and Service Guide - Page 41

Heading, Option, Description, Update Address Only appears if Custom is selected in Update Source

Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Heading Option Management Operations Option ROM Launch Policy Network BIOS Update Update BIOS via Network Description - Runtime Power Management-(Enable or Disable) - Idle Power Savings-Extended (default) or Normal; extended mode reduces processor power consumption when the processor is idle. - Unique Blink States-(Enable or Disable) ● Thermal Options-Lets you set the rate of the system fan when the processor is in idle. ● Hardware Power Options - After Power Loss (On, Off, Previous State)-"On" means the system will power on again after power is restored. "Off" means it will remain shut down after power is restored. "Previous State" directs the previous state to be the default after power is restored. - S4/S5 Max Power Savings (Disables/Enabled) Lets you set the following AMT (Intel Active Management Technology) configuration options: ● AMT-(Enabled/Disabled) Allows for remote discovery, repair and protection of networked workstations. Enabling the AMT function also enables the Network Controller (required for AMT to function correctly). ● Unconfigure AMT/ME-(Disabled/Enabled) Restores AMT/ME defaults. When you save and exit after enabling this option, you will be prompted to complete the process upon restart. A Setup Password (even if one is set) does not need to be entered to complete the process. NOTE: Information about Intel AMT can be found at www.intel.com. ● Hide Un-Configure ME Confirmation Prompt-(Disabled/Enabled) ● WatchDog Timer-(Enabled/Disabled) OS and BIOS WatchDog Timers can be set independently (in minutes): - OS WatchDog Timer-Sets the OS WatchDog Timer - BIOS WatchDog Timer-Sets the BIOS WatchDog Timer ● PXE Option ROMS-(Legacy, UEFI Only, Do Not Launch) ● Storage Option ROMS-(Legacy, UEFI Only, Do Not Launch) ● Video Option ROMS-(Legacy, UEFI Only) ● Configurations ● Check for Updates Now ● Update BIOS via Network-(Enable/Disable) ● Update Source-(HP, Custom) ● Update Address (Only appears if Custom is selected in Update Source) ● Automatic BIOS Update Setting-(Enable/Disable) For more information about Updae BIOS via Network, go to http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/action.process/ public/psi/mostViewedDisplay/? sp4ts.oid=5403903&javax.portlet.action=true&spf_p.tpst=psiContentDisplay&javax.por tlet.begCacheTok=com.vignette.cachetoken&spf_p.prp_psiContentDisplay=wsrpinteractionState%3DdocId%253Demr_na-c04119260%257CdocLocale %253Den_US&javax.portlet.endCacheTok=com.vignette.cachetoken. Computer Setup (F10) Utility 31

Section	Page
Hardware overview	11
HP Z440 Workstation components	11
HP Z440 Workstation front panel components	12
HP Z440 Workstation rear panel components	13
HP Z440 Workstation chassis components	14
HP Z440 Workstation system board components	15
HP Z440 Workstation system board architecture	16
HP Z440 Workstation specifications	16
HP Z640 Workstation components	18
HP Z640 Workstation front panel components	18
HP Z640 Workstation rear panel components	19
HP Z640 Workstation chassis components	20
HP Z640 Workstation system board components	21
HP Z640 Workstation system board architecture	22
HP Z640 Workstation system board riser architecture	23
HP Z640 Workstation specifications	23
HP Z840 Workstation components	25
HP Z840 Workstation front panel components	25
HP Z840 Workstation rear panel components	26
HP Z840 Workstation chassis components	27
HP Z840 Workstation system board components	28
HP Z840 Workstation system board architecture	29
HP Z840 Workstation specifications	30
Environmental specifications	31
Ensuring proper ventilation	32
System management	33
Power management features	33
ERP compliance mode	33
Hyper-Threading Technology (HTT)	34
SATA Power Management	34
Intel Turbo Boost Technology	34
BIOS ROM	34
Computer Setup (F10) Utility	35
Computer Setup (F10) Utility functions	35
Accessing Computer Setup (F10) Utility	36
Computer Setup (F10) Utility menu	37
Desktop management	42
Initial computer configuration and deployment	43
Installing a remote system	43
Copying a setup configuration to another computer	43
Updating and managing software	44
LANDesk Software	44
HP Driver Pack	44
HP SoftPaq Download Manager	44
HP System Software Manager	45
ROM Flash	45
Remote ROM Flash	45
HPQFlash	45
FailSafe Boot Block	45
Recovering the computer from Boot Block Recovery mode	46
Workstation security	46
Asset tracking	46
SATA hard drive security	47
DriveLock applications	47
Using DriveLock	48
Enabling DriveLock	48
Password security	49
Establishing a setup password using Computer Setup (F10) Utility	49
Establishing a power-on password using computer setup	49
Entering a power-on password	50
Entering a setup password	50
Changing a power-on or setup password	50
Deleting a power-on or setup password	51
National keyboard delimiter characters	52
Clearing passwords	52
Chassis security	52
Smart Cover Sensor	52
Setting the protection level	53
Cable lock (optional)	53
Fault notification and recovery	53
ECC fault prediction	53
Thermal sensors	53
Dual-state power button	53
Changing the power button configuration (Windows only)	54
Component replacement information and guidelines	55
Warnings and cautions	55
Service considerations	56
Tools and software requirements	56
Electrostatic discharge (ESD) information	56
Product recycling	58
Component replacement guidelines	58
Battery	58
Cable management	59
Processor and processor heatsink	60
Expansion slots	61
Card configuration restrictions for power supplies	61
Choosing an expansion card slot	61
HP Z440 Workstation slot identification and description	62
HP Z440 Workstation installation sequence recommendations	63
HP Z640 Workstation slot identification and description	64
HP Z640 Workstation installation sequence recommendations	64
HP Z840 Workstation slot identification and description	66
HP Z840 Workstation installation sequence recommendations	67
Hard drives and optical drives	69
Handling hard drives	69
Removal and replacement tips	69
Drive installation and cabling scenarios	69
HP Z440 Workstations — Intel AHCI SATA controller guidelines	70
HP Z440 Workstations — LSI 9217-4i4e RAID controller guidelines	71
HP Z640 Workstations — Intel AHCI SATA controller guidelines	72
HP Z640 Workstations — LSI 9217-4i4e RAID controller guidelines	73
HP Z840 Workstation cabling guidelines	74
Memory	75
Supported DIMM configurations	75
BIOS errors and warnings	75
DIMM installation guidelines	75
HP Z440 Workstation DIMM installation order	76
HP Z640 Workstation DIMM installation order	77
HP Z840 Workstation DIMM installation order	78
Power supply	79
Power supply specifications	79
HP Z440 power supply specifications	79
HP Z640 power supply specifications	80
HP Z840 power supply specifications	81
Power consumption and heat dissipation	82
Resetting the power supply	82
System board	82
System cabling	83
HP Z440 Workstation system cabling	83
HP Z640 Workstation system cabling	84
HP Z840 Workstation system cabling	85
Diagnostics and troubleshooting	86
Calling support	86
Locating ID labels	87
Locating warranty information	87
Diagnosis guidelines	88
Diagnosis at startup	88
Diagnosis during operation	88
Troubleshooting checklist	88
HP troubleshooting resources and tools	89
Online support	89
Troubleshooting a problem	89
Instant Support and Active Chat	89
Customer Advisories, Customer and Security Bulletins, and Customer Notices	90
Product Change Notifications	90
Helpful hints	90
At startup	90
During operation	91
Customer Self-Repair program	91
Troubleshooting scenarios and solutions	92
Solving minor problems	92
Solving hard drive problems	94
Solving display problems	95
Solving audio problems	97
Solving printer problems	98
Solving power supply problems	98
Testing power supply	98
Diagnostic codes and errors	100
Diagnostic LED and audible (beep) codes	100
LED color definitions	102
POST error messages	102
Using HP PC Hardware Diagnostics (UEFI)	107
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device	107
Additional BIOS crisis recovery tool	108
Using Remote HP PC Hardware Diagnostics (UEFI) settings	108
Customizing Remote HP PC Hardware Diagnostics (UEFI) settings	108
Configuring password security and resetting CMOS	109
Preparing to configure passwords	109
Resetting the password jumper	110
Clearing and resetting the CMOS	111
Using the CMOS button to reset CMOS	111
Using Computer Setup (F10) Utility to reset CMOS	112
Linux technical notes	113
System RAM	113
Audio	113
Network cards	114
Hyper-Threading Technology	114
NVIDIA Graphics Workstations	114
AMD Graphics Workstations	115
Configuring RAID devices	116
RAID hard drive maximum and associated storage controller options	116
Supported RAID configurations	117
Configuring Intel SATA RAID	118
Configuring system BIOS	118
Configuring RAID with the Intel utility	119
Configuring RAID on an LSI 2308 or LSI 9217-4i4e controller	120
RAID 0 configuration	120
RAID 1 configuration	121
RAID 1E/10 configuration	122
Configuring RAID on an LSI 9270-8i MegaRAID controller	123
RAID 0	123
Software RAID solution	124
Software RAID considerations	124
Performance considerations	124
Configuring software RAID	125
System board designators	126
HP Z440 and Z640 Workstation system board designators	126
HP Z840 Workstations	128
Statement of Volatility	131
Z440 Workstation	131
Z640 Workstation	131
Z840 Workstation	132

Match case Limit results 1 per page

Heading

Option

Description

—

Runtime Power Management—(Enable or Disable)

—

Idle Power Savings—Extended (default) or Normal; extended mode reduces

processor power consumption when the processor is idle.

—

Unique Blink States—(Enable or Disable)

●

Thermal Options—Lets you set the rate of the system fan when the processor is in

idle.

●

Hardware Power Options

—

After Power Loss (On,

Oﬀ,

Previous State)—”On” means the system will

power on again after power is restored.

“Oﬀ”

means it will remain shut down

after power is restored. “Previous State” directs the previous state to be the

default after power is restored.

—

S4/S5 Max Power Savings (Disables/Enabled)

Management

Operations

Lets you set the following AMT (Intel Active Management Technology)

conﬁguration

options:

●

AMT—(Enabled/Disabled) Allows for remote discovery, repair and protection of

networked workstations. Enabling the AMT function also enables the Network

Controller (required for AMT to function correctly).

●

Unconﬁgure

AMT/ME—(Disabled/Enabled) Restores AMT/ME defaults. When you

save and exit after enabling this option, you will be prompted to complete the

process upon restart. A Setup Password (even if one is set) does not need to be

entered to complete the process.

NOTE:

Information about Intel AMT can be found at www.intel.com.

●

Hide

Un-Conﬁgure

Conﬁrmation

Prompt—(Disabled/Enabled)

●

WatchDog Timer—(Enabled/Disabled) OS and BIOS WatchDog Timers can be set

independently (in minutes):

—

OS WatchDog Timer—Sets the OS WatchDog Timer

—

BIOS WatchDog Timer—Sets the BIOS WatchDog Timer

Option ROM Launch

Policy

●

PXE Option ROMS—(Legacy, UEFI Only, Do Not Launch)

●

Storage Option ROMS—(Legacy, UEFI Only, Do Not Launch)

●

Video Option ROMS—(Legacy, UEFI Only)

Network BIOS Update

●

Conﬁgurations

●

Check for Updates Now

Update BIOS via

Network

●

Update BIOS via Network—(Enable/Disable)

●

Update Source—(HP, Custom)

●

Update Address (Only appears if Custom is selected in Update Source)

●

Automatic BIOS Update Setting—(Enable/Disable)

For more information about Updae BIOS via Network, go to

http://h20565.www2.hp.com/

portal/site/hpsc/template.PAGE/action.process/

public/psi/mostViewedDisplay/?

sp4ts.oid=5403903&javax.portlet.action=true&spf_p.tpst=psiContentDisplay&javax.por

tlet.begCacheTok=com.vignette.cachetoken&spf_p.prp_psiContentDisplay=wsrp-

interactionState%3DdocId%253Demr_na-c04119260%257CdocLocale

%253Den_US&javax.portlet.endCacheTok=com.vignette.cachetoken

Computer Setup (F10) Utility