HP Z840 Maintenance and Service Guide - Page 43

Initial computer configuration and deployment, Installing a remote system

Get HP Z840 PDF manuals and user guides View all HP Z840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Initial computer configuration and deployment The computer includes a preinstalled system software image. After a brief software unbundling process, the computer is ready to use. If you prefer to replace the preinstalled software image with a customized set of system and application software, you can deploy a customized software image using either of the following methods: ● Installing additional software applications after unbundling the preinstalled software image ● Using a disk-cloning process to copy the contents from one hard drive to another The ROM-based setup and Advanced Configuration and Power Interface (ACPI) hardware provide further assistance with recovery of system software, configuration management and troubleshooting, and power management. Support for specific features described in this guide can vary by model and software version. The best deployment method depends on the information technology environment and processes. Installing a remote system When the computer has been configured as a remote system, you can start it and set it up by using software and configuration information on a network server. This feature is usually used for system setup and configuration and can be used to perform the following functions: ● Deploy a software image on new PCs ● Format a hard drive ● Install application software or drivers ● Update the operating system, application software, or drivers To initiate a remote system installation, press F12 when F12=Network Service Boot appears in the lower right corner of the HP logo screen. Follow the onscreen instructions to continue the installation process. The default boot order can be changed in the BIOS so that the system always attempts to boot from the network. Copying a setup configuration to another computer This section provides information about replicating the computer setup. CAUTION: Setup configuration is model specific. File system corruption can result if source and target computers are not the same model. To copy a setup configuration: 1. Select a computer to use as the source of the setup configuration. 2. Connect a removable storage device to the computer, and then restart the computer. 3. As soon as the computer turns on, press and hold F10 until you enter Computer Setup (F10) Utility. If necessary, press Enter to bypass the title screen. NOTE: If you do not press F10 at the appropriate time, you must restart the computer, and then press and hold F10 to access the utility. 4. Select Main, select Replicated Setup, and then select Back up current settings to USB device. Follow the instructions on the screen to create the configuration file cpqsetup.txt and write it to a USB storage device. Desktop management 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
Initial computer
configuration
and deployment
The computer includes a preinstalled system software image. After a brief software unbundling process, the
computer is ready to use.
If you prefer to replace the preinstalled software image with a customized set of system and application
software, you can deploy a customized software image using either of the following methods:
●
Installing additional software applications after unbundling the preinstalled software image
●
Using a disk-cloning process to copy the contents from one hard drive to another
The ROM-based setup and Advanced
Configuration
and Power Interface (ACPI) hardware provide further
assistance with recovery of system software,
configuration
management and troubleshooting, and power
management.
Support for
specific
features described in this guide can vary by model and software version.
The best deployment method depends on the information technology environment and processes.
Installing a remote system
When the computer has been
configured
as a remote system, you can start it and set it up by using software
and
configuration
information on a network server. This feature is usually used for system setup and
configuration
and can be used to perform the following functions:
●
Deploy a software image on new PCs
●
Format a hard drive
●
Install application software or drivers
●
Update the operating system, application software, or drivers
To initiate a remote system installation, press
F12
when
F12=Network Service Boot
appears in the lower
right corner of the HP logo screen. Follow the onscreen instructions to continue the installation process. The
default boot order can be changed in the BIOS so that the system always attempts to boot from the network.
Copying a setup
configuration
to another computer
This section provides information about replicating the computer setup.
CAUTION:
Setup
configuration
is model
specific.
File system corruption can result if source and target
computers are not the same model.
To copy a setup
configuration:
1.
Select a computer to use as the source of the setup
configuration.
2.
Connect a removable storage device to the computer, and then restart the computer.
3.
As soon as the computer turns on, press and hold
F10
until you enter Computer Setup (F10) Utility. If
necessary, press
Enter
to bypass the title screen.
NOTE:
If you do not press
F10
at the appropriate time, you must restart the computer, and then press
and hold
F10
to access the utility.
4.
Select
Main
, select
Replicated Setup
, and then select
Back up current settings to USB device
. Follow
the instructions on the screen to create the
configuration
file
cpqsetup.txt
and write it to a USB
storage device.
Desktop management
33