HP nx9000 Reference Guide - Page 90

Startup problems, If the notebook stops responding after booting

Page 90 highlights

Troubleshooting and Maintenance Troubleshooting Your Notebook If the USB port is not working • Contact the vendor of the peripheral device for the latest USB drivers. • Check the port settings in Control Panel. Open the hardware Device Manager, then select Universal Serial Bus Controller. Startup problems If the notebook does not respond when you turn it on • Connect the AC adapter. • Reset the notebook by inserting the tip of a paper clip into the reset button on the bottom of the notebook. Then press the power button to turn it on. • If the notebook still doesn't respond, remove the battery and AC adapter, remove any PC Cards, and undock the notebook if docked. Then plug in the AC adapter again, and reset the notebook using the reset button. If the notebook won't boot from battery power • Make sure the battery is properly inserted and fully charged. Check the battery charge by removing it and pressing the pad on the side of the battery. The lights show the charge level. • If available, try another battery. If the notebook will not boot from the diskette drive • Make sure the diskette drive is selected as the boot device. See the "Basic Operation" chapter in this guide for directions. • If you're using a USB diskette drive, use the BIOS Setup utility to make sure Legacy USB Support is enabled. If your notebook also has a built-in diskette drive, use the BIOS Setup utility Boot menu to make sure the USB diskette drive is the first device under Removable Drive. If the notebook stops responding after booting Check whether you are connected to a TCP/IP network with no DHCP server. This can cause a long delay at startup because DHCP is enabled. Contact your network administrator to determine the proper TCP/IP configuration. Reference Guide 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121

Troubleshooting and Maintenance
Troubleshooting Your Notebook
Reference Guide
81
If the USB port is not working
Contact the vendor of the peripheral device for the latest USB drivers.
Check the port settings in Control Panel. Open the hardware Device Manager,
then select Universal Serial Bus Controller.
Startup problems
If the notebook does not respond when you turn it on
Connect the AC adapter.
Reset the notebook by inserting the tip of a paper clip into the reset button on the
bottom of the notebook. Then press the power button to turn it on.
If the notebook still doesn
t respond, remove the battery and AC adapter, remove
any PC Cards, and undock the notebook if docked. Then plug in the AC adapter
again, and reset the notebook using the reset button.
If the notebook won’t boot from battery power
Make sure the battery is properly inserted and fully charged. Check the battery
charge by removing it and pressing the pad on the side of the battery. The lights
show the charge level.
If available, try another battery.
If the notebook will not boot from the diskette drive
Make sure the diskette drive is selected as the boot device. See the
Basic
Operation
chapter in this guide for directions.
If you
re using a USB diskette drive, use the BIOS Setup utility to make sure
Legacy USB Support is enabled. If your notebook also has a built-in diskette
drive, use the BIOS Setup utility Boot menu to make sure the USB diskette drive
is the first device under Removable Drive.
If the notebook stops responding after booting
Check whether you are connected to a TCP/IP network with no DHCP server. This
can cause a long delay at startup because DHCP is enabled. Contact your network
administrator to determine the proper TCP/IP configuration.