IBM 8646 Hardware Maintenance Manual - Page 32

Message, Description, Explanation, Action, unloading AFT.NLM.

Get IBM 8646 - Eserver xSeries 220 PDF manuals and user guides View all IBM 8646 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Table 4. NetWare driver messages for the Ethernet controller (continued) Message Description Duplicate slot numbers Explanation: An attempt has been made to bind the same slot detected. number more than once. Action: Check the slot numbers entered during the bind. Adapter slot numbers must be valid and unique. If the problem persists, contact your network supplier. 'Xxx' is not supported Explanation: A bind command has been issued for adapters not for AFT team. supported by AFT.NLM. Action: Make sure that you attempt to bind only adapters supported by AFT.NLM. Primary and Secondary adapters do not match. AFT group is not created. Explanation: A bind command was entered for an adapter team that is a combination of server and client adapters. An AFT team must be a grouping of the same classification of adapter. Action: Verify that all the adapters bound in a team are of the same classification. Requested number of Secondary cards are not found. Explanation: The number of adapters specified in the bind command could not be located. Action: Verify the numbers and slot locations of the adapters to be bound. If the problem persists, contact your network supplier. Failed to create AFT Explanation: Binding of protocol failed. Protocol is either not group. Make sure that bound to any adapter or is bound to more than one adapter in the the drivers for group. Action: Ensure that the protocol is bound to only adapter supported adapters are in an AFT team. loaded, primary adapter is bound to protocols, and secondary adapter is not bound to any protocols. Error identifying slot numbers for the specified board names. Explanation: The mapping between the board name entered and the slot number for an adapter could not be established. Action: Check the board name for the adapter before issuing the bind command. If the problem persists, contact your network supplier. Can't unbind specified slot from AFT group. Make sure that the slot you specified is for the primary adapter in an AFT group. Explanation: The number entered in the unbind command was not the primary adapter in an AFT group. Action: Reissue the unbind command and specify the slot number for the primary adapter. LAN adapter at slot nnnn (Port 0xaa) failed to reset. Check the state of the adapter. Explanation: The adapter that you specified could not be initialized. Action: 1. Load the driver for the supported adapter. 2. Check that the adapter is seated properly in the slot and try loading the AFT module again. If the problem persists, contact your network supplier. AFT is not supported on this version of NetWare¬. Explanation: The NetWare on your server is not a version supported by AFT. Action: Load and bind AFT only on supported versions of NetWare (currently version 4.11 and above). Failed to allocate resources tags. Explanation: An unknown error has occurred when trying to allocate needed resources for the AFT module. Action: Check Server Configuration. If the problem persists, contact your network supplier. Please unload all LAN Explanation: An attempt was made to unload the AFT.NLM drivers before module before unloading the adapter driver. Action: Unload the unloading AFT.NLM. adapter driver before unloading the AFT module. 24 Hardware Maintenance Manual: xSeries 220 Type 8646

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
Table 4. NetWare driver messages for the Ethernet controller (continued)
Message
Description
Duplicate slot numbers
detected.
Explanation:
An attempt has been made to bind the same slot
number more than once.
Action:
Check the slot numbers entered
during the bind. Adapter slot numbers must be valid and unique.
If the problem persists, contact your network supplier.
’
Xxx
’
is not supported
for AFT team.
Explanation:
A bind command has been issued for adapters not
supported by AFT.NLM.
Action:
Make sure that you attempt to
bind only adapters supported by AFT.NLM.
Primary and
Secondary adapters do
not match. AFT group
is not created.
Explanation:
A bind command was entered for an adapter team
that is a combination of server and client adapters. An AFT team
must be a grouping of the same classification of adapter.
Action:
Verify that all the adapters bound in a team are of the same
classification.
Requested number of
Secondary cards are
not found.
Explanation:
The number of adapters specified in the bind
command could not be located.
Action:
Verify the numbers and
slot locations of the adapters to be bound. If the problem persists,
contact your network supplier.
Failed to create AFT
group. Make sure that
the drivers for
supported adapters are
loaded, primary
adapter is bound to
protocols, and
secondary adapter is
not bound to any
protocols.
Explanation:
Binding of protocol failed. Protocol is either not
bound to any adapter or is bound to more than one adapter in the
group.
Action:
Ensure that the protocol is bound to only adapter
in an AFT team.
Error identifying slot
numbers for the
specified board names.
Explanation:
The mapping between the board name entered and
the slot number for an adapter could not be established.
Action:
Check the board name for the adapter before issuing the bind
command. If the problem persists, contact your network supplier.
Can
’
t unbind specified
slot from AFT group.
Make sure that the slot
you specified is for the
primary adapter in an
AFT group.
Explanation:
The number entered in the unbind command was
not the primary adapter in an AFT group.
Action:
Reissue the
unbind command and specify the slot number for the primary
adapter.
LAN adapter at slot
nnnn
(Port 0x
aa
) failed
to reset. Check the
state of the adapter.
Explanation:
The adapter that you specified could not be
initialized.
Action:
1.
Load the driver for the supported adapter.
2.
Check that the adapter is seated properly in the slot and try
loading the AFT module again.
If the problem persists, contact your network supplier.
AFT is not supported
on this version of
NetWare
¬
.
Explanation:
The NetWare on your server is not a version
supported by AFT.
Action:
Load and bind AFT only on supported
versions of NetWare (currently version 4.11 and above).
Failed to allocate
resources tags.
Explanation:
An unknown error has occurred when trying to
allocate needed resources for the AFT module.
Action:
Check
Server Configuration. If the problem persists, contact your
network supplier.
Please unload all LAN
drivers before
unloading AFT.NLM.
Explanation:
An attempt was made to unload the AFT.NLM
module before unloading the adapter driver.
Action:
Unload the
adapter driver before unloading the AFT module.
24
Hardware Maintenance Manual: xSeries 220 Type 8646