IBM 8646 Hardware Maintenance Manual - Page 54

Removing the bezel, Attention

Get IBM 8646 - Eserver xSeries 220 PDF manuals and user guides View all IBM 8646 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

1. Review the information in "System reliability considerations" on page 44. 2. Turn off the server and all attached devices and disconnect power cords and then all external cables. 3. If necessary, unlock the server cover. 4. Pull out on the cover-release latch near the rear of the server cover; then, slide the cover toward the rear of the server and remove it. Attention: For proper cooling and airflow, replace the cover before turning on the server. Operating the server for extended periods of time (over 30 minutes) with the cover removed might damage server components. 5. For a tower model, rotate the stabilizing feet on the bottom of the server, and place the server on its side to install or remove components. Removing the bezel The following illustration shows how to remove the bezel from the server. Note: The illustrations in this document might differ slightly from your hardware. Do the following to remove the bezel: 1. Review the information in "System reliability considerations" on page 44. 2. Turn off the server and peripheral devices and disconnect all power cords and then all external cables. 3. Remove the side cover (see "Removing the side cover" on page 45). 4. Press the bezel-release latch at the top of the server to disconnect the top of the bezel from the server. 5. Release the two tabs at the top edge of the bezel and pull the top of the bezel slightly away from the server. 6. Pull the bezel up to release the two tabs at the bottom edge of the bezel. Store the bezel in a safe place. 46 Hardware Maintenance Manual: xSeries 220 Type 8646

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
1.
Review the information in
“
System reliability considerations
”
on page 44.
2.
Turn off the server and all attached devices and disconnect power cords and
then all external cables.
3.
If necessary, unlock the server cover.
4.
Pull out on the cover-release latch near the rear of the server cover; then, slide
the cover toward the rear of the server and remove it.
Attention:
For proper cooling and airflow, replace the cover before turning
on the server. Operating the server for extended periods of time (over 30
minutes) with the cover removed might damage server components.
5.
For a tower model, rotate the stabilizing feet on the bottom of the server, and
place the server on its side to install or remove components.
Removing the bezel
The following illustration shows how to remove the bezel from the server.
Note:
The illustrations in this document might differ slightly from your hardware.
Do the following to remove the bezel:
1.
Review the information in
“
System reliability considerations
”
on page 44.
2.
Turn off the server and peripheral devices and disconnect all power cords and
then all external cables.
3.
Remove the side cover (see
“
Removing the side cover
”
on page 45).
4.
Press the bezel-release latch at the top of the server to disconnect the top of the
bezel from the server.
5.
Release the two tabs at the top edge of the bezel and pull the top of the bezel
slightly away from the server.
6.
Pull the bezel up to release the two tabs at the bottom edge of the bezel. Store
the bezel in a safe place.
46
Hardware Maintenance Manual: xSeries 220 Type 8646