IBM 8646 Hardware Maintenance Manual - Page 73

Installing the bezel, bezel snap into place.

Get IBM 8646 - Eserver xSeries 220 PDF manuals and user guides View all IBM 8646 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

v If you removed the microprocessor from connector (U11), press down on the latches on either side of connector (J12), and remove the VRM from connector (J12). v If you removed the microprocessor from connector (U12), press down on the latches on either side of connector (J42), and remove the VRM from connector (J42). 8. If you have other options to install or remove, do so now; otherwise, replace the support bracket assembly; then, go to "Installing the cover". Installing the bezel Do the following to install the bezel: 1. Insert the two tabs on the bottom of the bezel into the matching slots in the server chassis. 2. Push the top of the bezel toward the server until the two tabs at the top of the bezel snap into place. Installing the cover The following information describes the cover installation procedure. Note: The illustrations in this document might differ slightly from your hardware. Cover-release latch Key lock Note: If you removed the support bracket assembly after you removed the cover, reinstall it before you install the cover. Installing options 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
v
If you removed the microprocessor from connector (U11), press down on
the latches on either side of connector (J12), and remove the VRM from
connector (J12).
v
If you removed the microprocessor from connector (U12), press down on
the latches on either side of connector (J42), and remove the VRM from
connector (J42).
8.
If you have other options to install or remove, do so now; otherwise, replace
the support bracket assembly; then, go to
“
Installing the cover
”
.
Installing the bezel
Do the following to install the bezel:
1.
Insert the two tabs on the bottom of the bezel into the matching slots in the
server chassis.
2.
Push the top of the bezel toward the server until the two tabs at the top of the
bezel snap into place.
Installing the cover
The following information describes the cover installation procedure.
Note:
The illustrations in this document might differ slightly from your hardware.
Key lock
Cover-release
latch
Note:
If you removed the support bracket assembly after you removed the cover,
reinstall it before you install the cover.
Installing options
65