IBM 8646 Hardware Maintenance Manual - Page 89

Hot-swap backplane

Get IBM 8646 - Eserver xSeries 220 PDF manuals and user guides View all IBM 8646 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Hot-swap backplane Before you begin: v Read "Safety information" on page 111. v Review the information in "System reliability considerations" on page 44. Note: The illustration above may differ slightly from your server. To remove the hot-swap backplane, do the following: 1. Power-off the server, if it is on. 2. Unplug the server. 3. Remove the front bezel (see "Removing the bezel" on page 46). 4. Remove the cover (see "Removing the side cover" on page 45). 5. Remove the support bracket (see "Removing the support bracket assembly" on page 47). 6. Remove any hard disk drives or drive fillers from the drives. 7. Disconnect the hard disk drive cables that connect to the system board. 8. Swing the cage out. 9. Slide the backplane out of the cage. FRU information (service only) 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
Hot-swap backplane
Before you begin:
v
Read
“
Safety information
”
on page 111.
v
Review the information in
“
System reliability considerations
”
on page 44.
Note:
The illustration above may differ slightly from your server.
To remove the hot-swap backplane, do the following:
1.
Power-off the server, if it is on.
2.
Unplug the server.
3.
Remove the front bezel (see
“
Removing the bezel
”
on page 46).
4.
Remove the cover (see
“
Removing the side cover
”
on page 45).
5.
Remove the support bracket (see
“
Removing the support bracket assembly
”
on
page 47).
6.
Remove any hard disk drives or drive fillers from the drives.
7.
Disconnect the hard disk drive cables that connect to the system board.
8.
Swing the cage out.
9.
Slide the backplane out of the cage.
FRU information (service only)
81