IBM 8659-71Y Maintenance Manual - Page 46

NDIS 4.0 Windows NT Driver Messages, UNIX Messages

Get IBM 8659-71Y - Netfinity 5000 - 8659 PDF manuals and user guides
UPC - 087944526346
View all IBM 8659-71Y manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

NDIS 4.0 (Windows NT) Driver Messages: The following error messages are for the NDIS 4.0 drivers. The explanation and recommended action are included with each message. PermaNet(tm) Server: No Secondary Adapter Found. Grouping Mode is disabled. Explanation: The failover option requires an adapter that is compatible with the device driver of the Ethernet controller on the system board. No such adapter was found. Action: Make sure the correct adapter is installed. . PermaNet(tm) Server: Problem Occurs on the Primary Adapter. Switching over to the Secondary Adapter. Explanation: The system detected a problem with the primary Ethernet connection and has transferred all network traffic to the secondary Ethernet controller. Action: Identify the cause of the failure on the primary Ethernet connection. Restoring the operational state of the primary connection will cause the network traffic to automatically transfer to the primary Ethernet controller. PermaNet(tm) Server: Switching back to Primary Adapter. Explanation: The primary Ethernet connection is now operating correctly. Network traffic will automatically transfer to the primary Ethernet controller. Action: None needed, message is for information only. . UNIX Messages: The following error messages are for the SCO UNIX LLI driver. pnt0-2 PCI search specified, PCI device not found! Explanation: The driver cannot locate the Ethernet controller on the PCI bus. Action: Run the NETCONFIG program to search for another Ethernet controller. Verify that the PCI Ethernet device type is set to the default (enabled) position in the Configuration/Setup utility programs (see "PCI Bus Control" on page 30). If the problem persists, go to "Diagnostic Test Programs" on page 11 to run the diagnostic utility. pnt0-6 Cannot allocate memory for the adapter during an interrupt. Please check your Streams parameters. Explanation: On a SunSoft Solaris system, this message indicates that the system is out of Streams memory blocks. Action: Use the CRASH utility to increase the number of Streams memory blocks. Modify the interrupt request (IRQ) settings in the Configuration/Setup utility programs, or run the NETCONFIG program to match the hardware settings. pnt0-7 Cannot allocate memory for the adapter during reset. Please check your Streams parameters. Explanation: The system is out of Streams memory blocks. Action: Use the CRASH utility to increase the number of Streams memory blocks. pnt0-11 Device not found! Explanation: The driver cannot find an Ethernet controller. Action: Verify that the PCI Ethernet device type is set to the default (enabled) position in the Configuration/Setup utility programs (see "PCI Bus Control" on page 30). If the Ethernet adapter is enabled, go to "Diagnostic Test Programs" on page 11 to run the diagnostic utility. 38 Netfinity Server HMM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
NDIS 4.0 (Windows NT) Driver Messages:
The following error messages are for the NDIS 4.0 drivers.
The explanation and recommended action are included
with each message.
PermaNet(tm) Server: No Secondary Adapter Found. Grouping Mode is
disabled.
Explanation:
The failover option requires an adapter that is compatible with
the device driver of the Ethernet controller on the system board.
No such
adapter was found.
Action:
Make sure the correct adapter is installed.
.
PermaNet(tm) Server: Problem Occurs on the Primary Adapter. Switching
over to the Secondary Adapter.
Explanation:
The system detected a problem with the primary Ethernet
connection and has transferred all network traffic to the secondary Ethernet
controller.
Action:
Identify the cause of the failure on the primary Ethernet connection.
Restoring the operational state of the primary connection will cause the
network traffic to automatically transfer to the primary Ethernet controller.
PermaNet(tm) Server: Switching back to Primary Adapter.
Explanation:
The primary Ethernet connection is now operating correctly.
Network traffic will automatically transfer to the primary Ethernet controller.
Action:
None needed, message is for information only.
.
UNIX Messages:
The following error messages are
for the SCO UNIX LLI driver.
pnt0-2
PCI search specified, PCI device not found!
Explanation:
The driver cannot locate the Ethernet controller on the PCI bus.
Action:
Run the NETCONFIG program to search for another Ethernet
controller.
Verify that the PCI Ethernet device type is set to the default (enabled) position
in the Configuration/Setup utility programs (see “PCI Bus Control” on
page 30).
If the problem persists, go to “Diagnostic Test Programs” on page
11 to run
the diagnostic utility.
pnt0-6
Cannot allocate memory for the adapter during an
interrupt.
Please check your Streams parameters.
Explanation:
On a SunSoft Solaris system, this message indicates that the
system is out of Streams memory blocks.
Action:
Use the CRASH utility to increase the number of Streams memory
blocks.
Modify the interrupt request (IRQ) settings in the Configuration/Setup utility
programs, or run the NETCONFIG program to match the hardware settings.
pnt0-7
Cannot allocate memory for the adapter during reset.
Please check your Streams parameters.
Explanation:
The system is out of Streams memory blocks.
Action:
Use the CRASH utility to increase the number of Streams memory
blocks.
pnt0-11
Device not found!
Explanation:
The driver cannot find an Ethernet controller.
Action:
Verify that the PCI Ethernet device type is set to the default
(enabled) position in the Configuration/Setup utility programs (see “PCI Bus
Control” on page
30).
If the Ethernet adapter is enabled, go to “Diagnostic
Test Programs” on page
11 to run the diagnostic utility.
38
Netfinity Server HMM