IBM 92296GU User Guide - Page 49

Removing, internal, drive-bay, bracket

Get IBM 92296GU - IntelliStation M - Pro 9229 PDF manuals and user guides
UPC - 000435957559
View all IBM 92296GU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Removing the internal drive-bay bracket To remove the internal drive-bay bracket, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 29. 2. Turn off the computer and all attached devices (see "Turning off the computer" on page 19). 3. Remove the side cover (see "Removing the side cover" on page 35). 4. If a hard disk drive is installed in the bracket, disconnect the signal and power cables from the hard disk drive. 5. Remove the two screws that fasten the top edge of the drive-bay bracket to the chassis. 6. Grasp the lower edge of the drive-bay bracket, and disengage it from the chassis. 7. Lift the top edge of the drive-bay bracket from the chassis and remove the drive-bay bracket from the computer. Screws Alignment tabs Chapter 4. Installing optional devices 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Removing
the
internal
drive-bay
bracket
To
remove
the
internal
drive-bay
bracket,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
29.
2.
Turn
off
the
computer
and
all
attached
devices
(see
“Turning
off
the
computer”
on
page
19).
3.
Remove
the
side
cover
(see
“Removing
the
side
cover”
on
page
35).
4.
If
a
hard
disk
drive
is
installed
in
the
bracket,
disconnect
the
signal
and
power
cables
from
the
hard
disk
drive.
5.
Remove
the
two
screws
that
fasten
the
top
edge
of
the
drive-bay
bracket
to
the
chassis.
6.
Grasp
the
lower
edge
of
the
drive-bay
bracket,
and
disengage
it
from
the
chassis.
7.
Lift
the
top
edge
of
the
drive-bay
bracket
from
the
chassis
and
remove
the
drive-bay
bracket
from
the
computer.
Screws
Alignment tabs
Chapter
4.
Installing
optional
devices
37