IBM 92296GU User Guide - Page 60

Installation

Get IBM 92296GU - IntelliStation M - Pro 9229 PDF manuals and user guides
UPC - 000435957559
View all IBM 92296GU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

1. Read the safety information that begins on page v, "Installation guidelines" on page 29, and the documentation that comes with the drive. 2. Turn off the computer and all attached devices; then, disconnect all external cables and power cords. 3. Remove the side cover (see "Removing the side cover" on page 35). 4. Remove the bezel (see "Removing the bezel" on page 36). 5. Touch the static-protective package that contains the drive to any unpainted metal surface on the computer; then, remove the drive from the package and place it on a static-protective surface. 6. Set any jumpers or switches on the new drive according to the documentation that comes with the drive. 7. To install the drive in bay 4, complete the following steps. To install a drive in bay 5 or 6 go to step 8. a. Lift up on the bottom edge of the internal drive-bay bracket and rotate the bracket out of the computer. b. Install the hard disk drive onto the hard disk drive tray, with the screws that come with the drive. Slide the drive into the bay until it snaps into place. If you are replacing the drive in bay 4, use the captured thumbscrew that you received earlier, to attach the drive to the chassis. c. Determine whether the drive is a SATA or SAS device; then, connect one end of the applicable signal cable into the back of the drive and make sure that the other end of this cable is connected into the applicable SATA or SAS connector. d. Route the signal cable so that it does not block the airflow to the rear of the drives or over the microprocessor and DIMMs. e. Connect the power cable to the back of the drive. The connectors are keyed and can be inserted only one way. If you have other devices to install, do so now; otherwise, go to "Completing the installation" on page 53. 8. To install the drive in bay 5 or bay 6, complete the following steps. Note: Before you can install a drive in bay 6, you must remove the plastic block from bay 6. a. Install the two shoulder screws, one on each side, at the front of the new drive. 48 IBM IntelliStation M Pro Type 9229: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
1.
Read
the
safety
information
that
begins
on
page
v,
“Installation
guidelines”
on
page
29,
and
the
documentation
that
comes
with
the
drive.
2.
Turn
off
the
computer
and
all
attached
devices;
then,
disconnect
all
external
cables
and
power
cords.
3.
Remove
the
side
cover
(see
“Removing
the
side
cover”
on
page
35).
4.
Remove
the
bezel
(see
“Removing
the
bezel”
on
page
36).
5.
Touch
the
static-protective
package
that
contains
the
drive
to
any
unpainted
metal
surface
on
the
computer;
then,
remove
the
drive
from
the
package
and
place
it
on
a
static-protective
surface.
6.
Set
any
jumpers
or
switches
on
the
new
drive
according
to
the
documentation
that
comes
with
the
drive.
7.
To
install
the
drive
in
bay
4,
complete
the
following
steps.
To
install
a
drive
in
bay
5
or
6
go
to
step
8.
a.
Lift
up
on
the
bottom
edge
of
the
internal
drive-bay
bracket
and
rotate
the
bracket
out
of
the
computer.
b.
Install
the
hard
disk
drive
onto
the
hard
disk
drive
tray,
with
the
screws
that
come
with
the
drive.
Slide
the
drive
into
the
bay
until
it
snaps
into
place.
If
you
are
replacing
the
drive
in
bay
4,
use
the
captured
thumbscrew
that
you
received
earlier,
to
attach
the
drive
to
the
chassis.
c.
Determine
whether
the
drive
is
a
SATA
or
SAS
device;
then,
connect
one
end
of
the
applicable
signal
cable
into
the
back
of
the
drive
and
make
sure
that
the
other
end
of
this
cable
is
connected
into
the
applicable
SATA
or
SAS
connector.
d.
Route
the
signal
cable
so
that
it
does
not
block
the
airflow
to
the
rear
of
the
drives
or
over
the
microprocessor
and
DIMMs.
e.
Connect
the
power
cable
to
the
back
of
the
drive.
The
connectors
are
keyed
and
can
be
inserted
only
one
way.
If
you
have
other
devices
to
install,
do
so
now;
otherwise,
go
to
“Completing
the
installation”
on
page
53.
8.
To
install
the
drive
in
bay
5
or
bay
6,
complete
the
following
steps.
Note:
Before
you
can
install
a
drive
in
bay
6,
you
must
remove
the
plastic
block
from
bay
6.
a.
Install
the
two
shoulder
screws,
one
on
each
side,
at
the
front
of
the
new
drive.
48
IBM
IntelliStation
M
Pro
Type
9229:
User’s
Guide