IBM 92296GU User Guide - Page 61

Power, signal, cables, internal, drives

Get IBM 92296GU - IntelliStation M - Pro 9229 PDF manuals and user guides
UPC - 000435957559
View all IBM 92296GU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Shoulder screws b. Position the hard disk drive so that the shoulder screws are aligned with the slots in the internal drive-bay bracket. c. Slide the front of the drive into the slots of the internal drive-bay bracket. Plastic block Guide slots Thumbscrew d. Lower the rear of the drive into position in the bracket, and install the thumbscrew at the rear of the drive. e. Reconnect the signal and power cables to the hard disk drive in the bracket. If you have other devices to install, do so now; otherwise, go to "Completing the installation" on page 53. Power and signal cables for internal drives Important: This computer is suitable for use on an IT power distribution system whose maximum phase to phase voltage is 240 V under any distribution fault condition. The computer uses cables to connect IDE, SATA, and SAS devices to the power supply and to the system board. (See "System-board internal connectors" on page 33 for the location of system-board connectors.) Review the following information before you connect power and signal cables to internal drives: Chapter 4. Installing optional devices 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Shoulder screws
b.
Position
the
hard
disk
drive
so
that
the
shoulder
screws
are
aligned
with
the
slots
in
the
internal
drive-bay
bracket.
c.
Slide
the
front
of
the
drive
into
the
slots
of
the
internal
drive-bay
bracket.
Guide slots
Thumbscrew
Plastic block
d.
Lower
the
rear
of
the
drive
into
position
in
the
bracket,
and
install
the
thumbscrew
at
the
rear
of
the
drive.
e.
Reconnect
the
signal
and
power
cables
to
the
hard
disk
drive
in
the
bracket.
If
you
have
other
devices
to
install,
do
so
now;
otherwise,
go
to
“Completing
the
installation”
on
page
53.
Power
and
signal
cables
for
internal
drives
Important:
This
computer
is
suitable
for
use
on
an
IT
power
distribution
system
whose
maximum
phase
to
phase
voltage
is
240
V
under
any
distribution
fault
condition.
The
computer
uses
cables
to
connect
IDE,
SATA,
and
SAS
devices
to
the
power
supply
and
to
the
system
board.
(See
“System-board
internal
connectors”
on
page
33
for
the
location
of
system-board
connectors.)
Review
the
following
information
before
you
connect
power
and
signal
cables
to
internal
drives:
Chapter
4.
Installing
optional
devices
49