Icom M605 User Manual - Page 108

Microphone installation, Installation

Get Icom M605 PDF manuals and user guides View all Icom M605 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

12 CONNECTIONS AND MAINTENANCE ■■Microphone installation Connect the supplied or optional HM-205 and the optional HM-195*1/HM-229 to the transceiver using the connection cable that comes with the transceiver or the microphone. The cable is required to operate the transceiver from a longer distance. You can also install the cable connector as a built-in plug on a cabinet or wall. To operate from even longer distances, connect the optional 6 meter long OPC-1541 extension cable between the transceiver and the microphone.*2 Up to two OPC-1541 can be added. *1Not usable for the IC-M605EURO. *2OPC-2384 coversion cable is required to connect the transceiver and HM-195/HM-229 command microphone or OPC-1541 extension cable. NOTE: The firmware of HM-195/HM-229 may be update when you connect them to the transceiver. DDInstallation 1. Insert the connection cable connector into the microphone connector or the command microphone jack, and tighten the nut. 2. To use the cable connector as a wall socket, install it as shown to the right. 3. Using the mounting base as a template, carefully mark the holes where the cable and 3 screws will be fastened. 98 4. Drill holes at these marks. 5. Install the mounting base using the supplied screws, as shown below. ••HM-205 Mounting base Nut Gasket Screw holes (approximately 2 (d) mm, 1/16 inch) ••HM-195/HM-229 Mounting base Cap Nut Gasket Screw holes (approximately 2 (d) mm, Cap 1/16 inch)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
98
98
12
CONNECTIONS AND MAINTENANCE
■
Microphone installation
Connect the supplied or optional HM-205 and the optional
HM-195*
1
/HM-229 to the transceiver using the connection
cable that comes with the transceiver or the microphone.
The cable is required to operate the transceiver from a
longer distance. You can also install the cable connector as
a built-in plug on a cabinet or wall.
To operate from even longer distances, connect the optional
6 meter long OPC-1541 extension cable between the
transceiver and the microphone.*
2
Up to two OPC-1541 can
be added.
*
1
Not usable for the IC-M605EURO.
*
2
OPC-2384
COVERSION
CABLE
is required to connect the transceiver
and HM-195/HM-229 command microphone or OPC-1541
extension cable.
NOTE:
The firmware of HM-195/HM-229 may be update
when you connect them to the transceiver.
D
Installation
1.
Insert the connection cable connector into the
microphone connector or the command microphone
jack, and tighten the nut.
2.
To use the cable connector as a wall socket, install it as
shown to the right.
3.
Using the mounting base as a template, carefully
mark the holes where the cable and 3 screws will be
fastened.
4.
Drill holes at these marks.
5.
Install the mounting base using the supplied screws, as
shown below.
•
HM-205
Mounting base
Nut
Cap
Gasket
Screw holes
(approximately 2 (d) mm,
1
/
16
inch)
•
HM-195/HM-229
Mounting base
Nut
Cap
Gasket
Screw holes
(approximately 2 (d) mm,
1
/
16
inch)