Insignia IS-HC040917 User Manual (English) - Page 38

No sound from the, substantial sound.

Get Insignia IS-HC040917 PDF manuals and user guides View all Insignia IS-HC040917 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Troubleshooting Problem Cause The sound suddenly The protection circuitry has been acti- goes off. vated because of a short circuit, etc. The sleep timer has turned the unit off. Remedy Check that the speaker wires are not touching each other and then turn this unit back on. Turn on the power, and play the source again. The sound is muted. Press MUTE to cancel a mute. Only the speaker on one side can be heard. Incorrect cable connections. Only the center speaker outputs substantial sound. When playing a monaural source with a pro-logic II listen mode the source signal is directed to the center channel, and the front and surround speakers output effect sounds. No sound from the The sound field programs are turned effect speakers. off. You are using a source or program combination that does not output sound from all channels. Connect the cables properly. If the problem persists. the cables may be defective. Select "6 stereo", another DSP mode or appropriate listen mode. Try another sound field program. No sound from the center speakers. The output level of the center speaker is set to minimum. "CENTER"in "Speaker Setting" is set to NONE. 2ch Stereo has been selected. Raise the level of the center speaker. Select the appropriate setting for the center speaker. Select "6 stereo", another DSP mode or appropriate listen mode. No sound from the surround speakers. The output level of the surround speakers is set to minimum. "SURR LR"in "Speaker Setting" is set to NONE. A monaural source is being played with "2 STEREO". Raise the output level of the surround speakers. Select the appropriate setting for the surround left and right speakers. Press "DSP" or "2/6STEREO"to turn on the sound fields or select "6 CH STEREO"mode. No sound from the surround center speaker. "Surround center" in "Speaker Setting" is set to NONE. The source or the listen selected mode does not contain surround center signals. Select the appropriate setting for the surround center speaker. Select "6 stereo"or another appropriate listen mode. NO sound from the "SW" in "Speaker Setting" is set to subwoofer. "NONE" when a Dolby Digital or DTS or other source signal is being played. The source does not contain low bass signals. Select "SW" is "YES". 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
Troubleshooting
Problem
Cause
Remedy
The sound suddenly
goes off.
The protection circuitry has been acti-
vated because of a short circuit, etc.
The sleep timer has turned the unit off.
Only the speaker
on one side can be
heard.
Check that the speaker wires are not touching
each other and
then turn this unit back on.
Turn on the power, and play the source again.
The sound is muted.
Press MUTE to cancel a mute.
Incorrect cable connections.
Connect the cables properly. If the problem
persists. the cables may be defective.
When playing a monaural source with
a pro-logic II
mode the source
signal is directed to the center
channel, and the front and surround
speakers output effect sounds.
listen
The sound field programs are turned
off.
Select "6 stereo", another DSP mode or
appropriate listen mode.
You are using a source or program
combination that does not output
sound from all channels.
Try another sound field program.
Only the center
speaker outputs
substantial sound.
No sound from the
effect speakers.
The output level of the center speaker
is set to minimum.
"CENTER"in "Speaker Setting
"
is set
to NONE.
Raise the level of the center speaker.
Select the appropriate setting for the center
speaker.
No sound from the
center speakers.
2ch Stereo has been selected.
Select "6 stereo", another DSP mode or
appropriate listen mode.
The output level of the surround
speakers is set to minimum.
Raise the output level of the surround speakers.
"SURR LR"in "Speaker Setting
"
is set
to NONE.
Select the appropriate setting for the surround
left and right speakers.
A monaural source is being played
with "2 STEREO".
Press "DSP" or
"2/6STEREO"to turn on the
sound
fields or select "6 CH STEREO"mode.
No sound from the
surround
speakers.
No sound from the
surround center
speaker.
"Surround center" in "Speaker Setting
"
is set to NONE.
Select the appropriate setting for the surround
center speaker.
Select "6 stereo"or another appropriate listen
mode.
NO sound from the
subwoofer.
"SW" in "Speaker Setting
"
is set to
"NONE" when a Dolby Digital or DTS
or other source signal is being played.
Select "SW" is "YES".
The source does not contain low bass
signals.
The source or the listen selected mode
does not contain surround center
signals.
37