Intel SR1560SF Service Guide - Page 52

Removing and Installing the Small Air Baffle - 1u server

Get Intel SR1560SF - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858196017
View all Intel SR1560SF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

3. Gradually and equally tighten each captive screw until each is firmly tightened. 2 3 4 1 AF002386 Figure 26. Installing the Heat Sink (1U Passive Heat Sink Shown) Removing a Processor 1. Loosen the four captive screws on the corners of the heat sink. 2. Twist the heat sink slightly to break the seal between the heat sink and the processor. 3. Lift the heat sink from the processor. If it does not pull up easily, twist the heat sink again. Do not force the heat sink from the processor. Doing so could damage the processor. 4. Lift the processor lever. 5. Raise the CPU load plate. 6. Remove the processor. Removing and Installing the Small Air Baffle Some installation processes will require that you remove the small air baffle that is placed behind the hard drive bays, near the front of your server. The steps below describe how to remove and then install the small air baffle. Use these steps only when it is necessary for a component installation process. 30 Intel® Server System SR1560SF Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
30
Intel
®
Server System SR1560SF Service Guide
3.
Gradually and equally tighten each captive screw until each is firmly tightened.
Figure 26. Installing the Heat Sink (1U Passive Heat Sink Shown)
Removing a Processor
1.
Loosen the four captive screws on the corners of the heat sink.
2.
Twist the heat sink slightly to break the seal between the heat sink and the
processor.
3.
Lift the heat sink from the processor. If it does not pull up easily, twist the heat sink
again. Do not force the heat sink from the processor. Doing so could damage the
processor.
4.
Lift the processor lever.
5.
Raise the CPU load plate.
6.
Remove the processor.
Removing and Installing the Small Air Baffle
Some installation processes will require that you remove the small air baffle that is placed
behind the hard drive bays, near the front of your server. The steps below describe how to
remove and then install the small air baffle. Use these steps only when it is necessary for a
component installation process.
AF002386
2
3
1
4