Intel SR1560SF Service Guide - Page 56

Installing and Removing a Fixed Hard Drive - rail

Get Intel SR1560SF - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858196017
View all Intel SR1560SF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

3. If you are not installing a new drive, place the drive blank into the drive carrier, using the four screws you removed from the hard drive. 4. With the black lever in the fully open position, slide the drive carrier into the server system. The green latch must be to the right. Do not push on the black lever until the lever begins to close by itself. Note: All hard drive carriers must be installed in the server system and populated with either a drive or a drive blank to maintain system thermals. 5. When the black lever begins to close by itself, push on it to lock the drive carrier into place. Installing and Removing a Fixed Hard Drive Cautions: Fixed mount hard drives are NOT hot-swappable. Before removing or replacing the drive, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and unplug the AC power cord from the system or wall outlet. Up to two fixed SATA drives can be installed in the Intel® Server System SR1560SF product code SR1560SF. Note: See "Server System References" for an Internet link to a list of supported hardware. Note: The extraction of fixed mount hard drives can only be performed by accessing the drive carrier latch from inside the chassis. Installing a Fixed Hard Disk Drive 1. Unlatch drive carrier from drive bay by pressing the latch at the end of the black drive rail and remove the hard drive carrier from the server system. 2. Remove the four screws securing the drive blank in place. Save the screws; you will use them to install the hard drive into the carrier. AF002380 Figure 33. Removing the Drive Blank from the Fixed Hard Drive Carrier 34 Intel® Server System SR1560SF Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
34
Intel
®
Server System SR1560SF Service Guide
3.
If you are not installing a new drive, place the drive blank into the drive carrier,
using the four screws you removed from the hard drive.
4.
With the black lever in the fully open position, slide the drive carrier into the server
system. The green latch must be to the right. Do not push on the black lever until
the lever begins to close by itself.
Note:
All hard drive carriers must be installed in the server system and populated with either a
drive or a drive blank to maintain system thermals.
5.
When the black lever begins to close by itself, push on it to lock the drive carrier
into place.
Installing and Removing a Fixed Hard Drive
Cautions:
Fixed mount hard drives are NOT hot-swappable. Before removing or replacing the drive,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
Up to two fixed SATA drives can be installed in the Intel
®
Server System SR1560SF -
product code SR1560SF.
Note:
See
“Server System References”
for an Internet link to a list of supported hardware.
Note:
The extraction of fixed mount hard drives can only be performed by accessing the drive
carrier latch from inside the chassis.
Installing a Fixed Hard Disk Drive
1.
Unlatch drive carrier from drive bay by pressing the latch at the end of the black
drive rail and remove the hard drive carrier from the server system.
2.
Remove the four screws securing the drive blank in place. Save the screws; you
will use them to install the hard drive into the carrier.
Figure 33. Removing the Drive Blank from the Fixed Hard Drive Carrier
AF002380