Intel SR1690WB Service Guide - Page 54

Pulling out the back lever, HDD Installation

Get Intel SR1690WB - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858210980
View all Intel SR1690WB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

A B AF003302 Figure 24. Pulling out the back lever 3. Remove the hard drive from its wrapper and place it on an antistatic surface. 4. Set any jumpers and/or switches on the drive according to the drive manufacturer's instructions. 5. With the drive circuit-side down, position the connector end of the drive so that it is facing the rear of the drive carrier. 6. Align the holes in the drive to the holes in the drive carrier and attach it to the carrier with the screws that were attached to the drive blank. B A AF003303 Figure 25. 2.5 HDD Installation 36 Intel® Server System SR1690WB Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
36
Intel
®
Server System SR1690WB Service Guide
Figure 24. Pulling out the back lever
3.
Remove the hard drive from its wrapper and place it on an antistatic surface.
4.
Set any jumpers and/or switches on the drive according to the drive manufacturer's
instructions.
5.
With the drive circuit-side down, position the connector end of the drive so that it is
facing the rear of the drive carrier.
6.
Align the holes in the drive to the holes in the drive carrier and attach it to the
carrier with the screws that were attached to the drive blank.
Figure 25. 2.5 HDD Installation
AF003302
A
B
AF003303
B
A