JVC GR-D33 Instruction Manual - Page 37
Audio Dubbing (GR-D93/73 only), Insert Editing (GR-D93/73 only
UPC - 074101484793
View all JVC GR-D33 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 37 highlights
EDITING EN 37 Audio Dubbing (GR-D93/73 only) Insert Editing (GR-D93/73 only) The audio track can be customized only when recorded in the 12-bit and SP modes. (੬ pg. 26) ● Use the provided remote control. Stereo Microphone PAUSE START/ STOP REW INSERT STOP PLAY A.DUB T W Speaker 1 Play back the tape to locate the point where editing will start, then press PAUSE (9). 2 While holding A. DUB (D) on the remote control, press PAUSE (9). The "9D" and "MIC" indicators appear. 3 Press PLAY (U), then begin "narrating". Speak into the microphone. ● To pause dubbing, press PAUSE (9). 4 To end Audio Dubbing, press PAUSE (9), then STOP (8). To hear the dubbed sound during playback Set "NARRATION" to "ON" or "MIX". (੬ pg. 25, 28) NOTES: ● Sound is not heard from the speaker during Audio Dubbing. ● When editing onto a tape that was recorded at 12-bit, the old and new soundtracks are recorded separately. ● If you dub onto a blank space on the tape, the sound may be disrupted. Make sure you only edit recorded areas. ● If feedback or howling occurs during TV playback, move the camcorder's microphone away from the TV, or turn down the TV's volume. ● If you change from 12-bit to 16-bit in mid-recording and then use the tape for Audio Dubbing, it is not effective from the point where 16-bit recording began. ● During Audio Dubbing, when the tape moves to scenes recorded in the LP mode, scenes recorded in 16-bit audio or a blank portion, Audio Dubbing stops. ● To perform Audio Dubbing while watching on the television, make connections. (੬ pg. 17) ● To perform Audio Dubbing with a video unit connected to the camcorder's AV connector, first set "S/AV INPUT" to "ON" in VIDEO Menu. (੬ pg. 25, 28) The "AUX" indication appears instead of "MIC". You can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in and outpoints. The original audio remains unchanged. ● Use the provided remote control. NOTES: ● Before performing the following steps, make sure that "TIME CODE" is set to "ON". (੬ pg. 25, 28) ● Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape. ● To perform Insert Editing while watching in the television, make connections. (੬ pg. 17) 1 Play back the tape, locate the Edit-Out point and press PAUSE (9). Confirm the time code at this point. (੬ pg. 13) 2 Press REW (3) until the Edit-In point is located, then press PAUSE (9). 3 Press and hold INSERT (I) on the remote control, then press PAUSE (9). The "9I" indicator and the Time Code (min.:sec.) appear and the camcorder enters Insert-Pause mode. 4 Press START/STOP to begin editing. ● Confirm the insert at the time code you checked in step 1. ● To pause editing, press START/STOP. Press it again to resume editing. 5 To end Insert Editing, press START/STOP, then STOP (8). NOTES: ● Program AE with special effects (੬ pg. 30) can be used to spice up the scenes being edited during Insert Editing. ● During Insert Editing, the date and time information changes. ● If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas. ● During Insert Editing, when the tape moves to scenes recorded in the LP mode or a blank portion, Insert Editing stops. (੬ pg. 43) ADVANCED FEATURES