JVC GY-HD200UB GY-HD200U Owner's Manual - Page 108

MENU SCREENS OTHERS[1/2] Menu Screen The OTHERS menu screen consists of two screens (1/2 screen, 2/2 screen) Item ANALOG OUT CHAR. Function/Setting (bold characters indicate initial settings) Sets whether or not to display characters such as status and menus on the screen for the [Y/PB/PR] and [VIDEO OUT] terminals. ON : On-screen display. OFF : No on-screen display. MEMO When ANALOG OUT CHAR. item is set to ON, the content displayed on the viewfinder is also displayed in the video from the video output terminal. During VTR recording, the mode is displayed in red on the viewfinder. However, color is not applied for the following video outputs. • Component output of recording or playback in DV format • Composite output SDI OUT CHAR. LONG PAUSE TIME ALARM VR LEVEL FRONT TALLY BACK TALLY FORMAT LED GENLOCK.. NEXT PAGE PAGE BACK Sets whether or not to display characters such as status and menus on the screen for the [HD/SD SDI] terminal. ON : On-screen display. OFF : No on-screen display. Selects the time (minutes) before the tape protect mode (drum head rotation stopped) is engaged when the recordstandby condition continues. 3MIN : 3 minutes 5MIN : 5 minutes * When used in a cold environment or when the stopped or STILL status continues, the setting will be 3 minutes or less regardless of the setting on the menu. * Normally, set "3MIN" and use this to prevent head clogging and tape damage. Selects whether or not alarm sound is emitted and the volume of the alarm sound. The alarm sound is output through the monitoring loudspeaker and the PHONES jack. OFF : Sound is not output. LOW : Alarm sound is soft. MIDDLE : Alarm sound is normal. HIGH : Alarm sound is loud. Selects the lighting method of the FRONT TALLY lamp during recording. BLINK : The lamp blinks from when the REC/VTR trigger is pressed and until recording starts. The lamp lights steadily during recording. ON : The lamp lights only during recording. OFF : The lamp is always off. Selects the lighting method of the BACK TALLY lamp during recording. BLINK : The lamp blinks from when the REC/VTR trigger is pressed and until recording starts. The lamp lights steadily during recording. ON : The lamp lights only during recording. OFF : The lamp is always off. Sets whether or not the [HDV/DV LED] g on page 15 lights for HDV format or DV format. ON : Lights. OFF : Does not light. Calls up the GENLOCK menu screen. Adjusts the H PHASE or SC PHASE of image signals of this device according to the external synchronization signal input to the [GENLOCK IN] terminal. X See page 99. To display the OTHERS[2/2] menu screen, move the cursor to this position and press the SHUTTER dial. The TOP MENU screen returns when the SHUTTER dial is pressed while the cursor is at this position. 96 OTHERS[2/2] Menu Screen * This is not displayed in VTR mode. Item 1394 REC TRIGGER* Function/Setting (bold characters indicate initial settings) Sets how to control the REC trigger command output from the IEEE1394 connector. (Can be displayed and set in camera mode) Set this when recording a backup of the HDV/DV signal from GY-HD250/GY-HD251 onto another device. OFF : Does not control the backup device. SYNCRO : Controls the backup device in conjunction with the recording start/stop mode status on this device, and if there is no videocassette or if no tape remains for recording, controls the backup device in conjunction with the REC trigger button and the lens VTR button on this device. SPLIT : The REC trigger button on the right panel of this device controls the backup device recording start/stop. Set this when you want to control the timing of the recording on this device and the backup device sep- arately. SERIES : Automatically starts recording on a backup device that is on Pause when the tape on this device has less than 3 minutes remaining during shooting. MEMO • If you use the backup recording function on the BR-HD50, set this item to OFF. • The cursor (K) does not move to this item when this device is recording. BACK SPACE [HDV]* This function controls the camera tape transport, back space and pre-roll time when the camera is connected to an external HDD or external back up Recorder via IEEE1394 in HDV mode. P-1394 : Priority for IEEE1394 recording (Auto setting) P-TAPE : Priority for camera VCR recording BACK SPACE [HDV] P-1394 P-TAPE IEEE1394 connection Connected and Power ON No connection or Power OFF See Note 4 Connected and Power ON No connection or Power OFF 1394 REC TRIGGER (X See page 97) OFF SYNCRO SPLIT SERIES OFF SYNCRO SPLIT SERIES OFF SYNCRO SPLIT SERIES OFF SYNCRO SPLIT SERIES Internal VCR start delay approx. 3 seconds External Recorder or HDD vie IEEE1394 terminal N/A See Note 1 See Note 2 N/A approx. 1 second N/A approx. 1 second approx. 1 second See Note 3 N/A N/A Note 1: REC start signal will be sent 3 seconds after pressing REC trigger button. * Actual recording start time is depending on recorder performance. Note 2: REC start signal will be sent just after pressing REC trigger button. * Actual recording start time is depending on recorder performance. Note 3: In this mode, the IEEE1394 stream is discontinuous during internal VCR back space editing (when the REC trigger is operated). This may result in breaks in the recording on tape on an external recorder. In the case of HDD recording this may result in this device staying in REC PAUSE or divided files. Note 4: If HD/SD SDI OUT on the VIDEO FORMAT[2/2] menu screen is set to ON, the internal VCR start delay becomes approximately 3 seconds. 97