JVC GY-HD200UB GY-HD200U Owner's Manual - Page 86
White Balance Adjustment, White Shading Adjustment
![]() |
UPC - 046838035616
View all JVC GY-HD200UB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 86 highlights
PREPARATIONS FOR OPERATION White Balance Adjustment Since the color of light (color temperature) varies depending on the light source, it is necessary to re-adjust the white balance when the main light source illuminating the subject changes. White Balance Adjustment Two kinds of white balance adjustment results can be stored in memories AUTO A and AUTO B. Adjustment procedure 1. Set the following switches. • Set the POWER switch to ON. • Set the IRIS mode switch of the lens to A (Auto). • Set the FULL AUTO switch to OFF. 2. Set the ND filter switch according to the current lighting. 3. Set the WHT.BAL switch to A or B. 4. Place a white object near the center of the screen under the same lighting conditions as the target subject and zoom in to fill the screen with white. 5. Press the AWB (Auto White Balance) button. "AUTO WHITE A, B OPERATION" is displayed in the viewfinder while the auto white balance adjustment circuit operates. When correct white balance is obtained, the approximate color temperature is displayed together with "AUTO WHITE A, B OK" for about 5 seconds. Iris mode switch (7 on page 10) ND filter AWB button WHT.BAL switch POWER switch MEMO Fine-tune red and blue to match the white adjusted in white balance in WHITE PAINT/ on the WHITE BALANCE menu screen. X See page 85. Error messages If the adjustment ends abnormally, an error message, as described below, blinks for about 5 seconds. • NG: OBJECT (Improper object) Displayed when there is not enough white color on an object or the color temperature is not suitable. Replace the color temperature conversion filter or use another white object and re-adjust the white balance. 52 • ERROR: LOW LIGHT (Insufficient illumination) Displayed when the illumination is dim. Increase the illumination and then re-adjust the white balance. • ERROR: OVER LIGHT (Excessive illumination) Displayed when the light is excessively bright. Decrease the illumination and then re-adjust the white balance. During operation Result message Improper object Insufficient illumination Excessive illumination CAUTION • Do not adjust using any highly reflective objects, such as metal, etc., as this may result in improper white balance adjustment. • The FAW (Full Auto White balance) function cannot provide optimum white balance with a subject outside the FAW adjustment range, for example when it contains only a single color or not enough white color. • The accuracy of the FAW (Full Auto White balance) is inferior to that of the Auto white balance. • When the power is turned on with the FAW mode selected, it takes about 10 seconds for the FAW adjustment to be completed. Do not shoot within this interval. Full Auto White Balance (FAW) The FAW function adjusts the white balance value automatically as the lighting condition changes. This mode is convenient when you have no time to adjust the white balance or when the camera is moved frequently in and out of places under different lighting conditions. Setting procedure The FAW function can be activated with the FAW item on the SWITCH MODE menu screen. The FAW function can be allocated to one of the white balance switching switches A, B, or PRESET. X See page 86. White Shading Adjustment Even if white balance is achieved in the middle of the screen, it may not be achieved at the top and bottom of the screen. Greens and magentas may be colored. This is due to characteristics of the lens. Correcting this phenomenon is called White Shading Adjustment. Perform this after adjusting white balance. White shading adjustment is performed on the WHITE BALANCE menu screen. 1. Display the WHITE BALANCE menu screen. Follow the steps in "Setting Menu Screens" on page 75 and proceed as follows. MENUrCAMERA PROCESS[1/2]rCAMERA PROCESS[2/2]rADVANCE PROCESSrWHITE BALANCE 4. Change the setting values for LEVEL(R), LEVEL(G), and LEVEL(B) with the SHUTTER dial while referring to the monitor. When setting values are increased, colors at the bottom of the screen are suppressed and the top is enhanced. LEVEL(R): Adjusts reds. LEVEL(G): Adjusts greens. LEVEL(B): Adjusts blues. 5. Press the SHUTTER dial after changing the setting val- ues to save in the memory. 6. Press the STATUS button to return to the normal screen. 7. When white shading adjustment is completed, adjust white balance again. X See "White Balance Adjustment" on page 52. Setting in the WHITE BALANCE screen is performed as follows. Selecting an item Turn the SHUTTER dial to align the cursor (j) with the desired item, and press the SHUTTER dial. • The item is selected and the setting value blinks. Changing the setting value Turn the SHUTTER dial to change the blinking value. When the SHUTTER dial is pressed, the value stops blinking and the setting is changed. 2. Perform the above steps to set SHADING to MANUAL. 3. Select LEVEL(R), LEVEL(G), LEVEL(B) and press the SHUTTER dial. • The setting value for the selected LEVEL blinks and becomes available for changing. 53
![](/manual_guide/products/jvc-gyhd200ub-gyhd200u-owners-manual-8327111/86.png)