JVC GY-HD200UB GY-HD200U Owner's Manual - Page 68

CONTROLS, INDICATORS AND CONNECTORS Left Side Section 98 7 1 2 3 CH2-AUDIO OUT-CH1 VIDEO IEEE 1394 0 6 5 4 1Viewfinder connector (6-pin) Connect the cable from the viewfinder here. • Set the image format for this terminal in VF SIGNAL on the LCD/VF[4/4] menu screen. X See page 92. 2[CH-2 INPUT] CH-2 audio input connector selector switch Selects the CH-2 audio input connector. INPUT1 INPUT2 : Inputs the audio from the INPUT1 connector 4 into CH-2. : Inputs the audio from the INPUT2 connector 4 into CH-2. MEMO The audio from the INPUT1 connector is also input into CH-1 regardless of the setting. 3[AUDIO INPUT] Audio input signal selector switch This switch is used to select the input sound signal from INPUT1 or INPUT2 connector. LINE : Set to this position when connected to audio equipment, etc. The reference input level is +4 dBs. MIC : Set to this position when the dynamic micro- phone is connected. MIC+48V : Set to this position when a microphone requiring +48 V power supply (phantom microphone, etc.) is connected. CAUTION When connecting a component that does not require +48 V power supply, make sure that the switch is not set to MIC+48V before the component is connected. MEMO You can select the normal input level for MIC and MIC+48V in the INPUT1, 2 MIC REF. item on the AUDIO/MIC[1/2] menu screen. X See page 87. 4[INPUT1/INPUT2] INPUT1/INPUT2 audio input connectors These are audio input connectors for connecting to an external audio device or microphone. • Set the [AUDIO INPUT] switch 3 according to the device to be connected. • Set the CH-2 audio input connector using the [CH-2 INPUT] switch 2. The CH-2 audio from the set connector is recorded. 5Shoulder pad slide button Button to adjust the position of the shoulder pad. When you press this button, you can move the position of the shoulder pad 6 forward or backward. 6Shoulder pad 7Cassette cover Sliding the EJECT switch a on page 18 located on the top section opens this cover to allow insertion or removal of the videocassette. CAUTION To prevent foreign objects from entering the internal parts of the VTR unit, do not leave this device with the cover open for extended periods of time. 8[VIDEO OUT] Video output terminal (RCA) This is a terminal for composite video signal output. • Select whether or not to output a signal with setup in SET UP on the VIDEO FORMAT[2/2] menu screen. (Only for U model) 9[AUDIO OUTPUT CH-1/CH-2] Audio output connector (RCA) Output connector for audio signals. • Outputs the input audio signal in the Camera mode. • Outputs the playback audio signal in the VTR mode. • When a HDV/DV signal (IEEE1394) is input, the EE sound of the input audio signal is output in the VTR mode. MEMO Alarm sound is not output. 0[IEEE1394] IEEE1394 connector (6-pin) Using an IEEE1394 cable (optional), a digital video component with IEEE1394 connector can be connected here. X See "Connecting the IEEE1394 Cable" on page 64. X See "HDV/DV Dubbing" on page 68. CAUTION When connecting the IEEE1394 cable, confirm that the connector is facing the right direction before inserting. X See page 64. MEMO Put the covers on the connectors when you are not using them. 16 cde CH2-AUDIO OUT-CH1 VIDEO g i h j IEEE 1394 f k a b a[STUDIO] Studio terminal (Round 10-pin) Connect the studio cable from the KA-HD250 Studio Kit (sold separately). Connect the KA-HD250 to use this device as a studio camera. For details, refer to the KA-HD250 INSTRUCTION MANUAL. b[DC INPUT] DC input terminal (XLR 4-pin) This is the 12V DC power input terminal. Connect to the AC adapter. When a battery is installed and a cable is connected to this terminal, power supply from the battery stops and power is supplied by this terminal. c[GENLOCK/AUX IN] GENLOCK/AUX IN switch Set according to the signal input in the [GENLOCK/AUX IN] terminal. GENLOCK : Set to this when inputting external synchronization signals. AUX IN : Set to this when inputting composite video signals from an external device. MEMO If no signals are input to the [AUX IN] terminal and this switch is set to AUX IN, the monitor turns black and video is not output from any terminal. d[PBPR/TC] PBPR/Time code switch Set according to the [PB/TC IN] and [PR/TC OUT] terminal signals. PBPR : Set to this when outputting component PB signals from the [PB/TC IN] terminal and outputting component PR signals from the [PR/TC OUT] terminal. TC : Set to this when inputting LTC time code from the [PB/TC IN] terminal and outputting the built-in time code generator from the [PR/TC OUT] terminal. MEMO When this switch is set to TC, video is not output from the Y/PB/PR terminal (i j k). e[IEEE1394] IEEE1394 switch Set according to the image format of the input/output signal and playback signal of the IEEE1394 terminal. HDV : Set to this for HDV format. DV : Set to this for DV format. f[REMOTE] REMOTE terminal (Round 6-pin) Some functions of this camera can be controlled externally. Connect to a remote control unit (RM-LP55/RM-LP57). X See "Connect a Remote Control Unit (RM-LP55/RMLP57)" on page 71. g[GENLOCK/AUX IN] GENLOCK/AUX IN terminal (BNC) • Input synchronization signals in this terminal when externally synchronizing camera images or playback images. Synchronization signal: BB (Black Burst) signal of SD or Tri sync signal of HD • Input composite video signals to record images from an external device with this device. • Select the signal to input with the [GENLOCK/AUX IN] switch c. X See "Using GENLOCK Functions" on page 66. X See "Recording Composite Video Signals from an External Device" on page 65. h[HD/SD-SDI] HD/SD-SDI output terminal (BNC) Outputs HD/SD-SDI (Serial Digital Interface) signals. Outputs embedded audio signals as digital audio. The sampling frequency for embedded audio is 48 kHz. In addition, the time code for the built-in time code generator and playback time code are output. X See pages 20 and 21 for the signals that are enabled. MEMO Set whether or not to output SDI signals from this terminal in HD/SD-SDI OUT of the VIDEO FORMAT[2/2] menu screen. i[Y] Component Y signal output terminal (BNC) Outputs Y signal of component when the [PBPR/TC] switch d is set to PBPR. j[PB/TC IN] Component PB signal output/time code input terminal (BNC) • Outputs PB signal of component when the [PBPR/TC] switch d is set to PBPR. • Inputs time code when the [PBPR/TC] switch d is set to TC. Enter the LTC time code to slave lock this device's time code generator with an external time code generator. MEMO Set TCG SOURCE on the TC/UB/CLOCK Menu screen to EXTERNAL to input external time codes. X See "Synchronizing with an External Time Code Generator" on page 49. k[PB/TC OUT] Component PB signal output/time code output terminal (BNC) • Outputs PR signal of component when the [PBPR/TC] switch d is set to PBPR. • Outputs the LTC time code of the built-in time code generator when the [PBPR/TC] switch d is set to TC. MEMO Set the [Y/PB/PR] terminal (i j k) output image signal to RGB or Y/C video signals in OUTPUT TERM. [DV] on the VIDEO FORMAT[2/2] menu screen. (Only for DV format) X See "OUTPUT TERM. [DV]" on page 79. 17