Kenwood TS-590SG Operation Manual - Page 13

[21 (7)] Press to select the 21 MHz band memory {page 11} or enter keypad number 7. [24 (8)] Press to select the 24 MHz band memory {page 11} or enter keypad number 8. [28 (9)] Press to select the 28 MHz band memory {page 11} or enter keypad number 9. [50 (0)] Press to select the 50 MHz band memory {page 11} or enter keypad number 0. [CLR] Press to exit from, abort, or reset various functions. Press and hold to clear a memory channel {page 46}. [ENT] Press to enter your desired frequency using the 10-key keypad {page 29}. -- D -- [LSB/USB] Press to select LSB or USB mode {page 11}. [CW/FSK (REV)] Press to select CW or FSK mode {page 11}. Press and hold to select a sideband (CW/ CW-R or FSK/ FSK-R). [FM/AM (FM-N)] Press to select FM or AM mode {page 11}. Press and hold to select Narrow FM mode. [DATA] Press to select a Data mode (LSB/ LSB-DATA, USB/ USB-DATA, FM/ FM-DATA, or AM-DATA) {page 11}. In CW mode, Press to toggle the Morse Code Decoder ON and OFF. Press and hold to enter the threshold level adjustment mode for Morse Code Decoder {page 38}. [FINE (F.LOCK)] Press to activate the Fine tuning function to allow more precise tuning {page 30}. Press and hold to activate the Frequency Lock function {page 56}. -- E -- Central (Tuning) control Turn to select the desired frequency {page 12}. Use the convenient finger-tip cavity for continuous tuning. Slide the lever underneath the Tuning control to the left or right to adjust the torque level of the control. Left makes the control light and right makes it heavy. light heavy TX-RX LED Lights red while transmitting and green when the squelch opens while receiving. GETTING ACQUAINTED 2 -- F -- [IF FIL] Press to toggle between IF Filter A and IF Filter B {page 40}. You can adjust the filter bandwidth using the LO/WIDTH and HI/SHIFT controls. Press and hold [IF FIL] to momentarily display each setting value of the current DSP filter DSP filter bandwidth {page 40}. [NB (LEV)] Press to cycle through Noise Blanker 1, Noise Blanker 2, and OFF. Press and hold to adjust the Noise Blanker level. When the Noise Blanker is OFF, press and hold to turn the Noise Blanker 1 and Noise Blanker 2 ON simultaneously {page 42}. [NR (LEV)] Press to cycle through the DSP Noise Reduction types: NR1, NR2, or OFF {page 41}. When the Noise Reduction function is turned ON, press and hold to change the parameters of the Noise Reduction function {page 42}. [BC (A.NOTCH)] Press to select the DSP Beat Cancel function, BC1 (Beat Cancel 1), BC2 (Beat Cancel 2) or OFF {page 41}. Press and hold to toggle the Auto Notch Filter ON and OFF {page 41}. [NOTCH (WIDE)] Press to toggle the IF Notch Filter ON or OFF {page 41}. Press and hold to set up the IF Notch bandwidth {page 41}. [SPLIT] Press to enter split-frequency operation, allowing you to use different transmission and reception frequencies {page 24}. Press and hold to enter the Split RX frequency setup mode. [TF-SET] During split-frequency operation, press to monitor or change your transmit frequency {page 24}. [A/B (A=B)] Press to select either VFO A or VFO B {page 10}. Press and hold to duplicate the data in the current VFO to the other VFO {page 25}. While in Menu mode, press to select Menu A or Menu B. While in Program Memory Channel mode, press to recall the start or end frequency. [M/V] Press to toggle between Memory and VFO modes. [M.IN] Press to enter Memory Scroll mode and to store data to a Memory channel {page 43}. [M>V] Press to transfer the current Memory Channel contents to the VFO. [Q-M.IN] Press to store data to the Quick Memory {page 46}. [Q-MR] Press to recall data from the Quick Memory {page 47}, while in VFO mode. Press to enter Memory Name Edit mode, while in Memory Channel mode {page 46}. [MHz] Press to turn the MHz Up/ Down function ON or OFF. The MHz digit increases or decreases when you turn the MULTI/CH control. In Menu mode, press to turn the Quick Menu ON or OFF {page 14}. 5