Kenwood TS-590SG Operation Manual - Page 82

RX Level Adjustment, TX Level Adjustment, Configuration for Switching the RX Bandwidth

Get Kenwood TS-590SG PDF manuals and user guides View all Kenwood TS-590SG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

13 CONNECTING PERIPHERAL EQUIPMENT ■ RX Level Adjustment Adjust the audio output level for receiving via data communication as necessary by using the sound setting (recording device) on the PC or using the following menus on the transceiver. * Refer to "Audio Level Settings" {page 62}. When using the USB audio function: Configure in Menu No. 72 (AUDIO LEVEL OF USB OUTPUT FOR DATA COMMUNICATIONS). When using the ACC 2 connector: Configure in Menu No. 74 (AUDIO LEVEL OF ACC2 OUTPUT FOR DATA COMMUNICATIONS). ■ TX Level Adjustment Adjust the audio input level for transmitting via data communication as necessary by using the sound setting (playback device) on the PC or using the following menus on the transceiver. * Refer to "Audio Level Settings" {page 62}. When using the USB audio function: Configure in Menu No. 71 (AUDIO LEVEL OF USB INPUT FOR DATA COMMUNICATIONS). When using the ACC 2 connector: Configure in Menu No. 73 (AUDIO LEVEL OF ACC2 INPUT FOR DATA COMMUNICATIONS). ■ Configuration for Switching the RX Bandwidth Configure the setting as follows to switch the RX bandwidth by cutting off the high or low frequencies within the frequency range of 0 Hz to 5000 Hz even in the SSB-DATA mode, in the same way as in SSB mode, during operations such as FT8. * Refer to "Filter control in SSB/ SSB-DATA mode (High/Low and Width/Shift)" {page 41}. Configure in Menu No. 29 (SSB DATA FILTER TYPE SELECTION). Select "1" (HI/LO). Note: ◆ USB cable and RS-232C straight cable are not supplied with this transceiver. Please purchase commercially available cables. ◆ Delays may occur when using USB audio, and there may also be audio interruptions depending on the performance and load of the PC. ◆ Place this transceiver far enough from the PC so that noise will not be picked up. ◆ For data communication software settings, refer to the instruction manual or Help file of the software in use. 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
74
13
CONNECTING PERIPHERAL EQUIPMENT
■
RX Level Adjustment
Adjust the audio output level for receiving via data communication as necessary by using the sound setting
(recording device) on the PC or using the following menus on the transceiver.
* Refer to “Audio Level Settings” {page 62}.
When using the USB audio function: Configure in Menu No. 72 (AUDIO LEVEL OF USB OUTPUT FOR DATA
COMMUNICATIONS).
When using the ACC 2 connector: Configure in Menu No. 74 (AUDIO LEVEL OF ACC2 OUTPUT FOR DATA
COMMUNICATIONS).
■
TX Level Adjustment
Adjust the audio input level for transmitting via data communication as necessary by using the sound setting
(playback device) on the PC or using the following menus on the transceiver.
* Refer to “Audio Level Settings” {page 62}.
When using the USB audio function: Configure in Menu No. 71 (AUDIO LEVEL OF USB INPUT FOR DATA
COMMUNICATIONS).
When using the ACC 2 connector: Configure in Menu No. 73 (AUDIO LEVEL OF ACC2 INPUT FOR DATA
COMMUNICATIONS).
■
Configuration for Switching the RX Bandwidth
Configure the setting as follows to switch the RX bandwidth by cutting off the high or low frequencies within the
frequency range of 0 Hz to 5000 Hz even in the SSB-DATA mode, in the same way as in SSB mode, during
operations such as FT8.
* Refer to “Filter control in SSB/ SSB-DATA mode (High/Low and Width/Shift)” {page 41}.
Configure in Menu No. 29 (SSB DATA FILTER TYPE SELECTION).
Select “1” (HI/LO).
Note:
◆
USB cable and RS-232C straight cable are not supplied with this transceiver. Please purchase commercially available cables.
◆
Delays may occur when using USB audio, and there may also be audio interruptions depending on the performance and load of the PC.
◆
Place this transceiver far enough from the PC so that noise will not be picked up.
◆
For data communication software settings, refer to the instruction manual or Help file of the software in use.