Home » Lantronix Manuals » Electronics Accessories » Lantronix MatchPort b/g » Manual Viewer

Lantronix MatchPort b/g MatchPort b/g - User Guide - Page 8

Updating Firmware, Wireless Bridging MatchPort b/g Only, Troubleshooting

View all Lantronix MatchPort b/g manuals

Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Contents 8: Updating Firmware 84 Obtaining Firmware 84 Reloading Firmware 84 Using TFTP: Graphical User Interface 84 Using TFTP: Command Line Interface 85 Recovering the Firmware Using the Serial Port 85 9: Wireless Bridging (MatchPort b/g Only) 86 10: Troubleshooting 87 Diagnostic LED States 87 Problems and Error Messages 88 Technical Support 90 MatchPort User Guide 8

Section	Page
MatchPort User Guide	1
Copyright and Trademark	2
Warranty	2
Contacts	2
Disclaimer	3
Table of Contents	5
List of Tables	9
List of Figures	9
1: Using This Guide	10
Purpose and Audience	10
Chapter Summary	10
Additional Documentation	11
2: Introduction	12
Capabilities	13
Applications	13
Protocol Support	13
Configuration Methods	14
Addresses and Port Numbers	14
Hardware Address	14
IP Address	14
Port Numbers	14
3: Using DeviceInstaller	15
Accessing the MatchPort Using DeviceInstaller	15
Viewing the MatchPort’s Current Configuration	16
4: Configuration Using Web-Manager	18
Accessing Web-Manager using DeviceInstaller	18
Network Configuration	20
Network Mode Configuration	20
Automatic IP Address Configuration	21
Static IP Address Configuration	22
Ethernet Configuration	23
Server Configuration	24
Host List Configuration	25
Channel 1 and Channel 2 Configuration	27
Serial Settings	27
Connection Settings - TCP	29
Connection Settings - UDP	32
Email Configuration	33
Trigger Configuration	34
WLAN Configuration (MatchPort b/g Only)	35
Configurable Pin Settings	39
Apply Settings	41
Apply Defaults	41
5: Configuration via Serial Mode or Telnet Port	42
Accessing Setup Mode	42
Telnet Access	42
Serial Port Access	43
Server Configuration	44
Network Mode (MatchPort b/g Only)	44
Set the IP Address	44
Set the Gateway IP Address	45
Set the Netmask	45
Set DNS Server IP Address	45
Change Telnet Configuration Password	45
DHCP Name	46
Channel 1 and Channel 2 Configuration	46
Baudrate	47
I/F (Interface) Mode	47
Flow	48
Port Number	48
Connect Mode	49
Send the Escape Sequence (+++) in Modem Mode	56
Show IP addr after 'RING'	56
Auto Increment Source Port	56
Remote IP Address	57
Remote Port	57
DisConnMode	57
Flush Mode	58
DisConnTime (Inactivity Timeout)	60
SendChar 1 and SendChar 2	60
Telnet Terminal Type	60
Channel (Port) Password	60
Email Configuration	60
Domain Name	62
Recipients	62
Triggers	62
WLAN Settings (MatchPort b/g Only)	63
Topology	64
Network Name (SSID)	64
Adhoc Network Channel	64
Security Suite	64
WEP	65
WPA	66
802.11i/WPA2-Personal	66
Fixed or Automatic Data Rate	67
Transmission Data Rate	67
Minimum TX Data Rate	67
Max TX Failures	67
Enable Power Management	67
Enable Soft AP Roaming	68
Expert Settings	68
TCP Keepalive Time	68
ARP Cache Timeout	69
CPU Performance	69
Disable Monitor Mode	69
HTTP Port Number	69
SMTP Port Number	69
MTU Size	69
TCP Re-transmission Timeout	70
Enable Alternate MAC	70
Ethernet Connection Type	70
Configurable Server Port Number (MatchPort b/g Only)	70
Automatic Host MAC Detection (MatchPort b/g Only)	70
Security Settings	71
Disable SNMP	71
SNMP Community Name	71
Disable Telnet Setup	71
Disable TFTP Firmware Update	71
Disable Port 77FE (Hex)	72
Disable Web Server	72
Disable Web Setup	72
Disable ECHO Ports	72
Enable Encryption	72
Enable Enhanced Password	73
Disable Port 77F0 (Hex)	73
Default Settings	73
Channel 1 and Channel 2 Configuration	73
WLAN Settings (MatchPort b/g Only)	74
Expert Settings	74
Security Settings	75
Email Settings	75
Exit Configuration Mode	75
6: Configurable Pins	76
Defaults Settings	76
Features	76
Control Protocol	76
Guidelines	76
Commands	77
Examples	79
7: Monitor Mode	81
Entering Monitor Mode via the Serial Port	81
Entering Monitor Mode via the Network Port	81
Monitor Mode Commands	81
8: Updating Firmware	84
Obtaining Firmware	84
Reloading Firmware	84
Using TFTP: Graphical User Interface	84
Using TFTP: Command Line Interface	85
Recovering the Firmware Using the Serial Port	85
9: Wireless Bridging (MatchPort b/g Only)	86
10: Troubleshooting	87
Diagnostic LED States	87
Problems and Error Messages	88