Lantronix XPort Pro XPort Pro - User Guide - Page 35

Line Command Mode, To con Command, Mode on a specific line

Get Lantronix XPort Pro PDF manuals and user guides View all Lantronix XPort Pro manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Line Command Mode Setting the Command Mode enables the CLI on the serial line. To configure Command Mode on a specific line: 1. Select Line on the menu bar, if you are not already in the Line web page. 2. Select a line number at the top of the page. 3. Select Command Mode. The Command Mode page for the selected line appears. 6: Line and Tunnel Settings Figure 6-4 Line 1 Command Mode 4. Enter or modify the following settings: Line - Command Mode Settings Mode Wait Time Table 6-5 Line Command Mode Description Select the method of enabling Command Mode or choose to disable Command Mode.  Always = immediately enables Command Mode for the serial line.  Use Serial String = enables Command Mode when the serial string is read on the serial line during boot time.  Use CP Group = enables Command Mode based on the status of a CP Group. When the value matches the current value of the group, Command Mode is enabled on the serial line.  Use both Serial String and CP Group = the serial string and the value of the CP group must be matched to enable Command Mode.  Disabled = turns off Command Mode. Enter the wait time for the serial string during boot-up in milliseconds. XPort Pro User Guide 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
6: Line and Tunnel Settings
XPort Pro User Guide
35
4.
Enter or modify the following settings:
Table 6-5
Line Command Mode
Line Command Mode
Setting the Command Mode
enables the CLI on the serial
line.
To configure Command
Mode on a specific line:
1.
Select
Line
on the menu
bar, if you are not already
in the Line web page.
2.
Select a line number at the
top of the page.
3.
Select Command Mode.
The Command Mode page
for the selected line
appears.
Figure 6-4
Line 1 Command Mode
Line – Command Mode
Settings
Description
Mode
Select the method of enabling Command Mode or choose to disable Command
Mode.
Always
= immediately enables Command Mode for the serial line.
Use Serial String
= enables Command Mode when the serial string is read
on the serial line during boot time.
Use CP Group
= enables Command Mode based on the status of a CP
Group. When the value matches the current value of the group, Command
Mode is enabled on the serial line.
Use both Serial String and CP Group
= the serial string and the value of
the CP group must be matched to enable Command Mode.
Disabled
= turns off Command Mode.
Wait Time
Enter the wait time for the serial string during boot-up in milliseconds.