Lantronix XPort Pro XPort Pro - User Guide - Page 53

To con modem emulation for a specific tunnel:, Tunnel, Modem Emulation

Get Lantronix XPort Pro PDF manuals and user guides View all Lantronix XPort Pro manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

6: Line and Tunnel Settings Table 6-20 Modem Emulation Commands and Descriptions (continued) Command (continued) AT&V AT&F AT&W ATZ ATS0=n ATA A/ Description Display current and saved settings. Reset settings in NVR to factory defaults. Save active settings to NVR. Restores the current state from the setup settings. Accept incoming connection.  N value of 0-Disable  N value of 1-Connect automatically  N value of 2+-Connect with ATA command. Answer incoming connection (if ATS0 is 2 or greater). Repeat last valid command. For commands that can take address information (ATD, ATDT, ATDP), the destination address can be specified by entering the IP Address, or entering the IP Address and port number. For example, :. The port number cannot be entered on its own. For ATDT and ATDP commands less than 255 characters, the XPort Pro replaces the last segment of the IP address with the configured Connect Mode remote station address. It is possible to use the last two segments also, if they are under 255 characters. For example, if the address is 100.255.15.5, entering "ATDT 16.6" results in 100.255.16.6. When using ATDT and ATDP, enter 0.0.0.0 to switch to the Command Line Interface (CLI). Once the CLI is exited by using the CLI exit command, the XPort Pro reverts to modem emulation mode. By default, the +++ characters are not passed through the connection. Turn on this capability using the modem echo pluses command. To configure modem emulation for a specific tunnel: 1. Select Tunnel on the menu bar, if you are not already in the Tunnel web page. 2. Select a tunnel number at the top of the page. 3. Select Modem Emulation. The Modem Emulation page for the specific tunnel appears. XPort Pro User Guide 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
6: Line and Tunnel Settings
XPort Pro User Guide
53
For commands that can take address information (ATD, ATDT, ATDP), the destination address
can be specified by entering the IP Address, or entering the IP Address and port number. For
example, <ipaddress>:<port>. The port number cannot be entered on its own.
For ATDT and ATDP commands less than 255 characters, the XPort Pro replaces the last
segment of the IP address with the configured Connect Mode remote station address. It is possible
to use the last two segments also, if they are under 255 characters. For example, if the address is
100.255.15.5, entering “ATDT 16.6” results in 100.255.16.6.
When using ATDT and ATDP, enter 0.0.0.0 to switch to the Command Line Interface (CLI). Once
the CLI is exited by using the CLI exit command, the XPort Pro reverts to modem emulation mode.
By default, the +++ characters are not passed through the connection. Turn on this capability
using the modem echo pluses command.
To configure modem emulation for a specific tunnel:
1.
Select
Tunnel
on the menu bar, if you are not already in the Tunnel web page.
2.
Select a tunnel number at the top of the page.
3.
Select
Modem Emulation
. The Modem Emulation page for the specific tunnel appears.
AT&V
Display current and saved settings.
AT&F
Reset settings in NVR to factory defaults.
AT&W
Save active settings to NVR.
ATZ
Restores the current state from the setup settings.
ATS0=n
Accept incoming connection.
N value of 0—Disable
N value of 1—Connect automatically
N value of 2+—Connect with ATA command.
ATA
Answer incoming connection (if ATS0 is 2 or greater).
A/
Repeat last valid command.
Table 6-20
Modem Emulation Commands and Descriptions (continued)
Command (continued)
Description