Lenovo NetVista Hardware Maintenance Manual (HMM) for Aptiva and NetVista 2255 - Page 62

Check IDE drive jumper. See 3.5-In. Hard Disk Drive Jumper Locations on BIOS Error Codes

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Table 2-1 BIOS Error Codes, Messages, and Beeps List BIOS Error Codes, Messages, beeps Action/FRU NOTE: To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause. 1762 Primary master IDE has changed Make sure that the System Boot Drive parameter in the Startup Options of BIOS Setup is not set to [Drive A only]. Load default settings in Setup. Primary slave IDE has changed Insert a system diskette into diskette drive and reboot system. Secondary master IDE has changed Secondary slave IDE has changed Make sure the diskette drive configuration setting in BIOS Setup is correct. Hard disk drives power. Diskette drive. System board. 1780 Primary master hard disk failure A warning message to indicate there has been a change of IDE Primary (Secondary) Channel Master (Slave) device. Load default settings in Setup. Check IDE drive jumper. See "3.5-In. Hard Disk Drive Jumper Locations" on page 126. 1781 IDE drive power. Primary slave hard disk failure IDE drive cable/connection. IDE drive. 1782 Secondary master hard disk failure A warning message to indicate there has been change of IDE Primary (Secondary) Channel Master (Slave) device. Load default settings in Setup. Check IDE drive jumper. See "3.5-In. Hard Disk Drive Jumper Locations" on page 126. 1783 IDE drive power. Secondary slave hard disk failure 8602 IDE drive cable/connection. IDE drive. Make sure the Mouse is connected properly and is set correctly in BIOS Setup. Mouse error on no Mouse present Mouse. System board. SYSTEM HALTED, (CTRLALT-DEL) TO REBOOT... Indicates the present boot attempt has been aborted and the system must be rebooted. Press and hold down the CTRL and ALT key and DEL. Hard Disk(s) failure (80) Hard Disk Drive reset failed. Hard Disk(s) failure (40) Hard Disk Drive controller diagnostics failed. Hard Disk(s) failure (20) Hard Disk Drive initialization error. Hard Disk(s) failure (10) Unable to recalibrate fixed disk. Non-System disk or disk error Insert a system disk into Drive A: and press . Replace and strike any key when ready If you assumed the system would boot from the hard drive, make sure the controller is inserted correctly and all cables are properly attached. Be sure the disk is formatted as a boot device. Then reboot the system. OFFENDING SEGMENT: This message is used in conjunction with the I/O CHANNEL CHECK and RAM PARITY ERROR messages when the segment that has caused the problem has been isolated. PRESS A KEY TO REBOOT This will be displayed at the bottom of the screen when an error occurs that requires you to reboot. Press any key and the system will reboot. 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
62
Table 2-1 BIOS Error Codes, Messages, and Beeps List
BIOS Error Codes,
Messages, beeps
Action/FRU
NOTE:
To diagnose a problem, first find the BIOS error messages, codes, or beeps in left column.
If directed to a check
procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed
in right column is the most likely cause.
1762
Primary master IDE has
changed
Primary slave IDE has changed
Secondary master IDE has
changed
Secondary slave IDE has
changed
Make sure that the System Boot Drive parameter in the Startup Options of BIOS Setup is
not set to [Drive A only].
Load default settings in Setup.
Insert a system diskette into diskette drive and reboot system.
Make sure the diskette drive configuration setting in BIOS Setup is correct.
Hard disk drives power.
Diskette drive.
System board.
1780
Primary master hard disk
failure
1781
Primary slave hard disk failure
A warning message to indicate there has been a change of IDE Primary (Secondary)
Channel Master (Slave) device.
Load default settings in Setup.
Check IDE drive jumper. See “3.5-In. Hard Disk Drive Jumper Locations” on page 126.
IDE drive power.
IDE drive cable/connection.
IDE drive.
1782
Secondary master hard disk
failure
1783
Secondary slave hard disk
failure
A warning message to indicate there has been change of IDE Primary (Secondary)
Channel Master (Slave) device.
Load default settings in Setup.
Check IDE drive jumper. See ”3.5-In. Hard Disk Drive Jumper Locations” on page 126.
IDE drive power.
IDE drive cable/connection.
IDE drive.
8602
Mouse error on no Mouse
present
Make sure the Mouse is connected properly and is set correctly in BIOS Setup.
Mouse.
System board.
SYSTEM HALTED, (
CTRL-
ALT-DEL
) TO REBOOT…
Indicates the present boot attempt has been aborted and the system must be rebooted.
Press and hold down the
CTRL
and
ALT
key and
DEL
.
Hard Disk(s) failure (80)
Hard Disk Drive reset failed.
Hard Disk(s) failure (40)
Hard Disk Drive controller diagnostics failed.
Hard Disk(s) failure (20)
Hard Disk Drive initialization error.
Hard Disk(s) failure (10)
Unable to recalibrate fixed disk.
Non-System disk or disk error
Replace and strike any key
when ready
Insert a system disk into Drive A: and press <
Enter
>.
If you assumed the system would boot from the hard drive, make sure the controller is
inserted correctly and all cables are properly attached.
Be sure the disk is formatted as a boot device. Then reboot the system.
OFFENDING SEGMENT:
This message is used in conjunction with the I/O CHANNEL CHECK and RAM PARITY
ERROR messages when the segment that has caused the problem has been isolated.
PRESS A KEY TO REBOOT
This will be displayed at the bottom of the screen when an error occurs that requires you to
reboot. Press any key and the system will reboot.