Lexmark C752 User Reference - Page 157

58 Too Many Flash Options 88 59 Incompatible 88 61 Defective Disk 88 62 Disk Full 88 63 Unformatted Disk 89 64 Disk Not Supported 89 64 Unsupported Disk Format 89 80 Fuser Maintenance 89 81 Engine Code CRC Failure 89 82 Waste Bottle Nearly Full 89 82 Waste Toner Bottle Full 89 82 Waste Toner Bottle Missing 89 83 ITU Maintenance 89 84 Oiler Nearly Exhausted 89 84 Replace Oiler 89 85 ITU Maintenance 90 86 ITU Maintenance 90 87 Fuser Missing 90 88 Toner Low 90 89 ITU Maintenance 90 900-999 Service 90 Activating Menu Changes 76 Bin Full 76 Busy 76 Canceling Fax 77 Canceling Job 77 Change 77 Check Connection 77 Clearing Job Accounting Stat 77 Close Door 77 Close Finisher Door 77 Close Tray X Door 77 Copying 77 Defragmenting 77 Delete All Jobs 77 Deleting Jobs 77 Disabling Menus 77 Disk Corrupted. Reformat? 77 Disk Recovery x/5 yyy% 78 Empty Hole Punch Box 78 Enabling Menus 78 Engine Warming 78 Enter PIN =___ 78 Fax 78 Flushing Buffer 78 Formatting Disk 78 Formatting Flash 78 Held Jobs may be lost 78 Held Jobs May Not Be Restored 79 Hole Punch Waste Full 79 Insert Staple Cartridge 79 Insert Tray 79 Install or Cancel Job 79 Invalid Engine Code 79 Invalid Network Code 79 Invalid Standard Network Code 79 ITU/Fuser Maint 79 Load Plain Letter 79 Load Manual 79 Load Staples 80 Load Tray 80 Menus Disabled 80 Network 80 Network , 80 Network Card Busy 80 No DRAM Installed 80 No Jobs Found. Retry? 80 Not Ready 80 Ovrflow Bin Full 80 Parallel 80 Performing Self Test 80 Power Saver 81 Print Jobs on Disk 81 Printer Calibrating 81 Printing Alignment Page 81 Printing Directory List 81 Printing Font List 81 Printing Job Accounting Stat 81 Printing Menu Settings 81 Prog Engine Code 81 Prog System Code 81 Program Flash 81 Programming Disk 81 Programming Error P 82 Queuing and Deleting Jobs 82 Queuing Jobs 82 Ready 82 Ready Hex 82 Reattach 82 Remove Paper 82 Resetting Active Bin 82 Resetting Fuser Cnt Value 82 Resetting the Printer 82 Restore Held Jobs. Go/Stop? 83 Restoring Factory Defaults 83 Restoring Held Job xxx/yyy 83 Restoring Held Jobs 83 Serial 83 Setup Required 83 Staples Low 83 Std Bin Full 83 Supplies 83 Tray Empty 83 Tray Low 83 Tray Missing 84 USB 84 Waiting 84 Multipage Border (Finishing Menu) 47 Multipage Order (Finishing Menu) 47 multipage print border settings 47 configuring 47 order settings 47 view settings 48 Multipage Print (Finishing Menu) 47 Multipage View (Finishing Menu) 48 multipurpose feeder, configuring 58 N Network Setup (Network Menu) 51 Network Buffer (Network Menu) 51 Network Menu 51 Job Buffering 51 MAC Binary PS 51 Network Setup 51 Network Buffer 51 NPA Mode 52 PCL SmartSwitch 52 PS SmartSwitch 52 Std Net Setup 52 network port configuring buffer size 51 NPA mode 52 PCL SmartSwitch 52 PS SmartSwitch 52 NPA Mode (Network Menu) 52 NPA Mode (Parallel Menu) 53 NPA Mode (Serial Menu) 66 NPA Mode (USB Menu) 73 NPA mode, setting network port 52 parallel port 53 serial port 66 USB port 73 numbers, operator panel 17 numerical values, selecting 16 O Offset Pages (Finishing Menu) 48 Oiler (Supplies Menu) 72 operator panel 16 buttons 16 numbers 17 options verifying installation with menu settings page 135 157