Lexmark E340 User's Guide - Page 70

Print Timeout, Printer, Language, Resource Save, Toner Alarm, Waiting, Memory Full - toner cartridge

Get Lexmark E340 PDF manuals and user guides View all Lexmark E340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Understanding the operator panel Menu item Purpose Values Print Timeout To specify the amount of time (in seconds) the printer waits before printing the last page of a print job that does not end with a command to print the page. The print timeout counter does not start until Waiting appears on the display. Disabled The printer does not print the last page of a print job until one of the following occurs: • The printer receives enough information to fill the page. • The printer receives a Form Feed command. • You select Print Buffer from the Job Menu. 1...255 (90*) The printer prints the last page after the specified time. (Your printer may not support the entire range of values.) Printer Language To establish the default printer language used to communicate data from the computer to the printer. Note: Setting a printer language as the default does not prevent a software application from sending print jobs that use the other language. PCL Emulation PS Emulation* PPDS Emulation PCL emulation, compatible with Hewlett-Packard printers. PostScript emulation, compatible with Adobe PostScript language. PPDS emulation. Resource Save To determine what the printer does Off* with downloaded resources, such as fonts and macros stored in RAM, if the printer receives a job that requires more memory than is available. On Printer retains downloaded resources only until memory is needed. It then deletes those resources associated with the inactive printer language. Printer retains all downloaded resources for all printer languages during language changes and printer resets. If the printer runs out of memory, 38 Memory Full appears on the display. Toner Alarm To specify how the printer responds Off* when it is low on toner. An error message is displayed until someone replaces the toner cartridge. If an Auto Continue value is selected from the Setup Menu, the printer resumes printing after the specified timeout value. Single Printer stops printing, displays an error message, and sounds three quick beeps. Continuous Printer stops printing, displays an error message, and repeats three beeps every 10 seconds until the toner cartridge is replaced. Wait Timeout To specify the amount of time (in seconds) the printer waits to receive additional bytes of data from the computer. When this timeout expires, the print job is canceled. Note: Wait Timeout is only available when you use PostScript emulation. This menu item has no effect on PCL emulation print jobs. Disabled 15...65535 (40*) Disables Wait Timeout. Specifies the amount of time the printer waits for additional data before it cancels the job. Using the printer menus 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Using the printer menus
70
Understanding the operator panel
Print Timeout
To specify the amount of time (in
seconds) the printer waits before
printing the last page of a print job that
does not end with a command to print
the page. The print timeout counter
does not start until
Waiting
appears
on the display.
Disabled
The printer does not print the last page
of a print job until one of the following
occurs:
•
The printer receives enough
information to fill the page.
•
The printer receives a Form Feed
command.
•
You select Print Buffer from the Job
Menu.
1...255 (90*)
The printer prints the last page after
the specified time. (Your printer may
not support the entire range of values.)
Printer
Language
To establish the default printer
language used to communicate data
from the computer to the printer.
Note:
Setting a printer language as
the default does not prevent a software
application from sending print jobs that
use the other language.
PCL Emulation
PCL emulation, compatible with
Hewlett-Packard printers.
PS Emulation*
PostScript emulation, compatible with
Adobe PostScript language.
PPDS Emulation
PPDS emulation.
Resource Save
To determine what the printer does
with downloaded resources, such as
fonts and macros stored in RAM, if the
printer receives a job that requires
more memory than is available.
Off*
Printer retains downloaded resources
only until memory is needed. It then
deletes those resources associated
with the inactive printer language.
On
Printer retains all downloaded
resources for all printer languages
during language changes and printer
resets. If the printer runs out of
memory,
38 Memory Full
appears on
the display.
Toner Alarm
To specify how the printer responds
when it is low on toner.
Off*
An error message is displayed until
someone replaces the toner cartridge.
If an Auto Continue value is selected
from the Setup Menu, the printer
resumes printing after the specified
timeout value.
Single
Printer stops printing, displays an error
message, and sounds three quick
beeps.
Continuous
Printer stops printing, displays an error
message, and repeats three beeps
every 10 seconds until the toner
cartridge is replaced.
Wait Timeout
To specify the amount of time (in
seconds) the printer waits to receive
additional bytes of data from the
computer. When this timeout expires,
the print job is canceled.
Note:
Wait Timeout is only available
when you use PostScript emulation.
This menu item has no effect on PCL
emulation print jobs.
Disabled
Disables Wait Timeout.
15...65535 (40*)
Specifies the amount of time the
printer waits for additional data before
it cancels the job.
Menu item
Purpose
Values