Marantz UD5005 UD5005 User Manual - English - Page 42

Audio Setting

Get Marantz UD5005 PDF manuals and user guides View all Marantz UD5005 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

ENGLISH Audio Setting Settings for audio output are made. Audio Output Default settings are underlined. Setting items Setting details Coaxial For selecting the format output from the digital audio output terminals. Bitstream : For selecting if the device connected to the unit supports Dolby Digital or DTS Digital Surround. PCM : For selecting when the device connected to the unit does not support Dolby Digital or DTS Digital Surround. Off : For outputting no audio signal from the digital audio output terminal of the unit. HDMI For selecting the format output from the HDMI output terminals. For converting audio signals, see "About digital signal audio output" (vpage 49) Bitstream : For selecting when the device connected to the unit supports Dolby TrueHD/Dolby Digital Plus/Dolby Digital or DTS-HD/DTS Digital Surround. The output format is automatically selected according to the audio format or the number of channels supported by the connected HDMI device. PCM : For selecting when a device connected to the unit does not support Dolby TrueHD/Dolby Digital Plus/Dolby Digital or DTS-HD/DTS Digital Surround. Off : For outputting no audio signal from the HDMI output terminal of the unit. For converting audio signals, see "Digital Audio Signal Output" (vpage 49) NOTE If "BD audio mode" is set to "HD Audio Output" with MODE on the remote control, BD secondary audio and interactive audio are not output. Setting items Setting details Down Sampling For selecting the sampling rate output from the digital audio output terminal. Refer to the operation manual for the device connected to the unit, and make settings depending on the connected device. 48 kHz / 96 kHz / 192 kHz NOTE • For rights-protected content, the audio signal is down-sampled to 48 kHz, 16-bits, and output. • If the connected device does not support the sampling rate of 96 kHz or 192 kHz and the settings for the unit is made as 96 kHz or 192 kHz, much noise may be generated from the connected device. DRC Compresses the dynamic range of Dolby TruHD/Dolby Digital Plus/Dolby Digital Audio. Off : Dynamic range is not compressed. On : Dynamic range is compressed. Auto : Dynamic range of Dolby TrueHD audio is automatically compressed according to the material. Audio of Dolby TrueHD only is compressed. This setting compensates high volume to low and low volume to high when high volume is not desired at night. 38 Remote control operation buttons Displaying the menu Cancel the menu Move the cursor (Up/Down/Left/Right) Decision the setting Return to previous menu

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
38
ENGLISH
Audio Setting
Settings for audio output are made.
Audio Output
Default settings are underlined.
Setting items
Setting details
Coaxial
For selecting the format
output from the digital audio
output terminals.
Bitstream
: For selecting if the device connected to the unit supports
Dolby Digital or DTS Digital Surround.
PCM
: For selecting when the device connected to the unit does not
support Dolby Digital or DTS Digital Surround.
Off
: For outputting no audio signal from the digital audio output terminal
of the unit.
For converting audio signals, see “About digital signal audio output”
(
v
page 49)
.
HDMI
For selecting the format
output from the HDMI
output terminals.
Bitstream
: For selecting when the device connected to the unit supports
Dolby TrueHD/Dolby Digital Plus/Dolby Digital or DTS-HD/DTS Digital
Surround. The output format is automatically selected according to the
audio format or the number of channels supported by the connected
HDMI device.
PCM
: For selecting when a device connected to the unit does not support
Dolby TrueHD/Dolby Digital Plus/Dolby Digital or DTS-HD/DTS Digital
Surround.
Off
: For outputting no audio signal from the HDMI output terminal of the
unit.
For converting audio signals, see “Digital Audio Signal Output”
(
v
page 49)
.
NOTE
If “BD audio mode” is set to “HD Audio Output” with
MODE
on the
remote control, BD secondary audio and interactive audio are not output.
Setting items
Setting details
Down Sampling
For selecting the sampling
rate output from the digital
audio output terminal.
Refer to the operation manual for the device connected to the unit, and
make settings depending on the connected device.
48 kHz / 96 kHz / 192 kHz
NOTE
•
For rights-protected content, the audio signal is down-sampled to 48
kHz, 16-bits, and output.
•
If the connected device does not support the sampling rate of 96 kHz or
192 kHz and the settings for the unit is made as 96 kHz or 192 kHz, much
noise may be generated from the connected device.
DRC
Compresses the dynamic
range of Dolby TruHD/Dolby
Digital Plus/Dolby Digital
Audio.
Off
: Dynamic range is not compressed.
On
: Dynamic range is compressed.
Auto
: Dynamic range of Dolby TrueHD audio is automatically compressed
according to the material. Audio of Dolby TrueHD only is compressed.
This setting compensates high volume to low and low volume to high
when high volume is not desired at night.
Remote control operation
buttons
Displaying the menu
Cancel the menu
Move the cursor
(Up/Down/Left/Right)
Decision the setting
Return to previous menu